Generac Power Systems quietpact 85d Скачать руководство пользователя

Страница: 21 / 112

ELECTRICAL HAZARDS

• The generator covered by this manual produces dangerous

electrical voltages that can cause fatal electrical shock. Avoid

contact with bare wires, terminals, connections, etc., while the

unit is running. Ensure all appropriate covers, guards, and bar-

riers are in place before operating the generator. If work must

be done around an operating unit, stand on an insulated, dry

surface to reduce shock hazard.

• Do not handle any kind of electrical device while stand-

ing in water, while barefoot, or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• During installation onto the vehicle, properly ground (bond)

the generator either by solid mounting to the vehicle frame or

chassis, or by means of an approved bonding conductor. DO

NOT connect the bonding conductor to any generator part that

might be removed or disassembled during routine maintenance.

If the grounding conductor must be replaced, use only a flexible

conductor that is of No. 8 American Wire Gauge (AWG) copper

wire minimum.

• If the vehicle electrical circuits can be powered by any other

source of electricity (such as, a “dockside” power receptacle),

there must be no possibility of connecting the different power

sources to the vehicle’s circuits at the same time. The dock-

side (utility) power source must be positively isolated from the

vehicle’s circuits whenever the generator is operating. Failure

to isolate the vehicle’s circuits from the dockside power sup-

ply when the generator is running may result in damage to the

generator or in serious injury or death to dockside (utility) power

workers due to backfeed of electrical energy.

• In case of an accident caused by electric shock, immediately

shut down the source of electrical power. If this is not possi-

ble, attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a nonconducting

implement, such as, a rope or board, to free the victim from

the live conductor. If the victim is unconscious, apply first

aid, and get immediate medical help.

• Never wear jewelry when working on this equipment. Jewelry

can conduct electricity, resulting in electric shock, or may get

caught in moving components, causing injury.

FIRE HAZARDS

• For fire safety, the generator must be installed and maintained

properly. Installation always must comply with applicable

codes, standards, laws, and regulations. Adhere strictly

to local, state and national electrical and building codes.

Comply with regulations the Occupational Safety and Health

Administration (OSHA) has established. Also, ensure that the

generator is installed in accordance with the manufacturer’s

instructions and recommendations. Following proper installa-

tion, do nothing that might alter a safe installation and render

the unit in noncompliance with the aforementioned codes,

standards, laws, and regulations.

• Keep a fire extinguisher in the vehicle at all times. Extinguishers

rated “ABC” by the National Fire Protection Association are

appropriate for use on the recreational vehicle generator electrical

system. Keep the extinguisher properly charged, and be familiar

with its use. If there are any questions pertaining to fire extin-

guishers, consult the local fire department.

EXPLOSION HAZARDS

• Do not smoke around the generator. Wipe up any fuel or oil spills

immediately. Ensure that no combustible materials are left in the

generator compartment, or on or near the generator, as FIRE or

EXPLOSION may result. Keep the area surrounding the generator

clean and free from debris.

• All fuel types are potentially FLAMMABLE and/or EXPLOSIVE and

should be handled with care. Comply with all laws regulating the

storage and handling of fuels.

• Fuel supply lines must be properly installed, purged and leak-

tested according to applicable fuel-gas codes, before placing

this equipment into service. There must be no possibility of fuel

vapors entering the vehicle interior.

• It is required that an approved, flexible, nonconductive fuel line

between the generator fuel connection point and the rigid fuel

lines be installed.

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the

State of California to cause cancer, birth defects and

other reproductive harm.

Safety Rules

Содержание quietpact 85d

















































































































Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды

Generac Power Systems quietpact 85d, Руководство пользователя

Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды