Gemini GEM-P801, Руководство по установке

Страница: 23 / 28

23
System Troubles
Use the System Trouble chart on the following
page to determine the specific System
Trouble(s).
During normal panel operation the
H
SYSTEM
TROUBLE LED has the following two modes of
operation:
STEADY
1-7 possible trouble
groups, AC is present
FLASHING
1-7 possible trouble
groups, AC is not
present
Viewing System Trouble(s)
Press the
A4
key on the keypad.
To determine the System Trouble Group
Number, count the number of times the
H
SYSTEM TROUBLE LED blinks. The keypad
sounder will beep at the same rate that the
H
SYSTEM TROUBLE LED blinks.
To determine the System Trouble, note the zone
LED that is ON. Look up the specific system
trouble on the chart on the following page.
The
H
SYSTEM TROUBLE LED and keypad
sounder will continue to flash and beep. To view
the next System Trouble, if any, press the
E
key. Continue pressing the
E
key, if there are
no more system troubles to view, the system will
return to normal operation.
Note: System Troubles Groups 3 through 7 -
System Trouble Groups that have a zone or
smoke detector associated with the trouble,
such as RF low battery. The zone(s) of the
device with a low battery will be displayed by the
ZONE LED . For example, a wireless low
battery on zone 2 would beep the keypad
sounder 3 times and turn on zone 2 LED.
Audible System Trouble Indication - For all
system troubles, except when the only system
trouble is the loss of AC, the keypad will beep
once every 10 seconds. The keypad will continue
to beep until the reset button is pressed or the
trouble has been acknowledged by pressing the
C
key.
System Trouble Reporting
The following system troubles, when enabled to
report to Telco 1 [37-3] or Telco 3 [57-3], will send
the report code programmed in Trouble Report
[63] if reporting using a pulse format:
System Trouble Pulse Report Code
Bell Cut F1
2-Wire Fire Trouble F1
Rcvr Fail-to-Respond F1
Receiver Tamper F1
Receiver JAM F1
Tx Low Battery F1
Tx Supervisory Failure F1
Smoke Low Battery F1
Smoke Sup. Failure F1
If reporting using Point ID, a unique code will be
sent for each of the following System Troubles.
System Trouble Point ID Report Codes
Bell Cut CODE 1 321 G00 ZN000-BELL 1 TROUBLE
2-Wire Fire Trouble CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
Rcvr Fail-to-Respond CODE 1 382 G00 ZN000-SENSOR TROUBLE
Receiver Tamper CODE 1 145 G00 ZN000-EXP. MODL. TAMPER
Receiver JAM CODE 1 333 G00 ZN000-FIRE LOOP TRBLE
Tx Low Battery CODE 1 384 G00 ZN00n-RF TRAN LOW BATT
Tx Supervisory Failure CODE 1 381 G00 ZN00n-SUPERVSN LOSS RF
A 300 (SYSTEM TROUBLE RST) code is sent if a restore is
reported after multiple troubles.
System Trouble
Group #
Keypad SYSTEM Trouble
LED is flashing 1 time
indicating System Trouble
Group 1.
Keypad Sounder beeps 1 time
indicating System Trouble
EXAMPLE
-
LOW BATTERY SYSTEM TROUBLE DISPLAY
Zone LED(s)
is ON
indicates
(Specific Trouble)
Specific Trouble
Zone 2 LED is ON indicating
Low Battery. (1 Beep, LED 2)
Flashing
(System Trouble
Group Number)
Enter
A4
to enter System Trouble mode
and determine the specific trouble. Press any key to
view all system troubles.
ARM
ED
H
G E M I N I
2
STA
TUS
Beeping
(System Trouble
Group Number)
FIGURE 9 S
YSTEM
T
ROUBLE
E
XAMPLE