Gemini GEM-P801 Скачать руководство пользователя страница 21

Страница: 21 / 28

The requirements for Site Initiated Auto
Downloading are as follows:

1. Download Computer running PCPreset.
2. Program the telephone number of the

Download Computer in location [90]

Callback Telephone Number.

3. Program location [93] with the number of

the PCPreset account that is to be
downloaded.

PCPreset

1. Create the GEM-P801 account to be

downloaded using PCD-Windows
Quickloader Software.

1. Create a List using PCPreset.
2. Select the account by pressing

Select the desired account from the list of
PCD3000 accounts available. (The
location in the list is the

Auto Download

ID Number

[93])

3. Tag the list by entering

(

download)

4. Enter Standby Mode by entering

The Computer is now in STANDBY
Site

At the site perform the following three steps:

1. Arm the panel.
2. Disarm the panel.
3. Enter

. The panel will now

call the download computer running
PCPreset. PCPreset will answer the call,
establish a connection, and then
download the account that matches the

Auto Download ID Number

[93] with the

account of the same number in the list
that PCPreset is currently running.

Dealer Programming

[94]Dealer Code

The default Dealer Code is

4567

. Program

a new 4-digit Dealer Code. When the panel
is defaulted the Dealer Code will be
changed back to the default Dealer Code of

4567

only

if Dealer Code Lockout [96-1]

has not

been programmed.

[95]User 1 Code

The 1st User code is a program code as
well as an Arm/Disarm code. The default
User Code is

1234

. If User 1 Code

Lockout is programmed the User 1 Code
cannot be programmed from User Program
Mode.

[96]Dealer Options 1

(1) Dealer Code Lockout

- Program to

prevent the Dealer Code from changing
with a panel default.

(2) User 1 Code Lockout

- If programmed

the User 1 Code cannot be programmed
from User Program Mode.

(3) Household Fire

- Activates the

following UL required features:
There is a 4 hour re-sound of wireless
Smoke Low Battery and wireless Smoke
Supervisory system troubles.

•

An active System Battery test performed
every 4 hours instead of 24 hours and
Wireless Smoke Supervisory Timer is set
to 4 hours.

•

Fire Bell Timing is March Time.

•

Wireless Smoke Supervisory Time is
fixed at 4 hours.

(4) Fire Trouble on Fire LED

- Normally all

troubles are displayed on the

SYSTEM

TROUBLE LED, including Fire Trouble. If
required Fire Trouble can be displayed on the
Fire LED. Fire Trouble is indicated by a
steady

Fire LED.

[97]Dealer Options 2

(1) International Dialing Protocol

- No

dialing if no dial tone, 60 s between attempts
and 4 s wait for dial tone.

(2) Invert Bell Output

- Inverts the Bell

polarity and removes supervision from the
bell circuit.

(3) System Trouble Auto Restore

Normally, System troubles require
acknowledgment (View System Trouble) in
order to restore. If this option is selected
troubles will restore without requiring
acknowledgment.

(4) User 1 Code-Program only

- If enabled

User 1 Code will function only as the User
Program Code and will not Arm/Disarm the
panel.

Содержание GEM-P801





























Результаты поиска

Содержание GEM-P801

Отзывы:

Похожие инструкции для GEM-P801

Бренды по названию

Популярные бренды

Gemini GEM-P801, Руководство по установке

Результаты поиска

Содержание GEM-P801

Отзывы:

Похожие инструкции для GEM-P801

Бренды по названию

Популярные бренды