GEIGER GEIGER-Easy-ZIP 1.x Скачать руководство пользователя страница 6

Страница: 6 / 16

Gerhard Geiger GmbH & Co. KG | 100W1552

1118

V000

7. Information for the specialist electrician

Caution: Important installation instructions.

Please follow all instructions since

incorrect installation can lead to

the destruction of the motor and the

switching unit.

The operations with the service clamps may be accom-

plished only by an electrical specialist.
Motors with electronic limit stops can be connected in

parallel. In this case the maximum load of the switching

unit must not be exceeded.
When changing the running direction the switchover must

be effected through an off-position.
When changing the running direction the switchover time

must be at least 0.5 s.
With a three-phase network, please use the same external

conductor in order to control the UP and DOWN directions.
PVC cables are not suitable for equipment used outdoors

or exposed to prolonged high levels of UV radiation. These

cables should not be used if they are likely to touch metal

parts that can heat up to temperatures exceeding 70°C.
Connecting cables with plug connectors of the Hirschmann

Company are tested and approved with couplings of the

Hirschmann Company.
In order to prevent a malfunction caused by coupling,

the supply line (ref. NYM) from the actuator/switch to

the motor must not exceed 100 m in case of motors with

electronic end stops.

8. Connection of the setting switch

In order to set the end positions on SOLIDline motors, any setting

switch can be used that has a programming key or that allows a

simultaneous UP/DOWN command. In this case, the UP/DOWN keys

must be activated simultaneously instead of the programming key.

Connect setting cable to the connecting cable of the motor (see diagram on the back of the

setting switch). The assignment to the direction of rotation is dependent on the installation

situation of the drive. Then connect the setting switch to the 230V mains.

Article Number / Geiger setting switch
M56F152

with service terminal (D), 5 wires, SMI compatible

M56F153

with service terminal (CH), 5 wires, SMI compatible

M56F154

with service terminal (D), 4 wires

Electronic /

mechanical

limit stop

blue

brow

blac

green/yello

Mains: 230V / 50Hz

Mains:
230 V~/50 Hz

Service
terminals

Connecting cable
to limit stop

Programming
key

PROG

Setting cable
M56...

Direction
keys

LED

Содержание GEIGER-Easy-ZIP 1.x

















Результаты поиска

Содержание GEIGER-Easy-ZIP 1.x

Отзывы:

Похожие инструкции для GEIGER-Easy-ZIP 1.x

Бренды по названию

Популярные бренды

GEIGER GEIGER-Easy-ZIP 1.x, Оригинальная инструкция по сборке и эксплуатации

Результаты поиска

Содержание GEIGER-Easy-ZIP 1.x

Отзывы:

Похожие инструкции для GEIGER-Easy-ZIP 1.x

Бренды по названию

Популярные бренды