background image

918215/CP0407

56

Printed in U.S.A

SERVICE AND STORAGE

1448 PLUS

SERVICE EVERY 50 HOURS OR 
WEEKLY

Also complete the service checks in: “Service 
Every 10 Hours or Daily” on page 54.

Check Fan Belt

If the belt is worn, cut, cracked, or damaged, it 
should be replaced. Order a replacement belt from 
your Gehl dealer. Refer to the engine manual to 
learn proper belt replacement and tension 
adjustment procedures.

Check Hydraulic Oil Level

The fluid must be cool when checking the reservoir 
level (Fig. 35) or changing the filter. This reduces 
the possibility of overfilling the hydraulic system 
and potential injury due to hot fluid.

Fig. 35 - Checking Hydraulic Oil Level

WARNING

ALWAYS protect face and eyes whenever a 
pressure plug or cap is removed. NEVER 
assume that no pressure exists in a pressure 
vessel or system.

Before removing the fill plug (Fig. 36), release 
hydraulic system pressure by loosening the fill 
plug or the breather cap on the top of the backwall 
console (shown in “Change Hydraulic Filter” on 
page 59).

NOTE:

Use a 3/4” drive socket wrench handle 

to remove the fill plug.

Fig. 36 - Removing Fill Plug

IMPORTANT:

Be sure that no dirt or other 

foreign matter enters the hydraulic system 
while the cap is removed. DO NOT 
OVERFILL.

See “Lubricants” on page 47 for recommended 
hydraulic oils.

Check Battery Connections/Cables

Check cables for corrosion or loose connection.

NOTE:

The battery on the paver is warranted 

by the supplier. See the label on the top of the 
battery for warranty information.

Cleaning the Battery

Always keep the top of the battery clean. Clean the 
battery with a brush dipped in an alkaline solution 
(ammonia or baking soda and water). After the 
foaming has stopped, flush the top of the battery 
with clean water. If the terminals and cable 
connection clamps are corroded or dirty, 
disconnect the cables and clean the terminals and 
clamps with the same alkaline solution.

Hot

Cold

1.  Fill plug

1

Courtesy of Machine.Market 

Содержание 1448 Plus





















































































Отзывы: