background image

Printed in U.S.A

17

918215/CP0407

SAFETY

(Continued)

Always wear safety glasses with side shields 
when striking metal against metal. In addition, 
it is recommended that a softer (chip-resistent) 
material be used to cushion the blow, such as a 
brass drift. Failure to follow could lead to 
serious injury to the eyes or other parts of the 
body.

Do not refill the fuel tank when the engine is 
hot. Allow engine to cool before refilling to 
prevent the hot engine from igniting any 
spilled or splashed fuel. 

Do not smoke while filling the fuel tank, while 
working on the fuel or hydraulic systems, or 
while working around the battery or propane 
heater. 

Do not attempt to loosen or disconnect any 
hydraulic lines, hoses or fittings without first 
relieving hydraulic circuit pressure. Also, be 
careful not to touch any hydraulic components 
that have been in recent operation, because 
they can be extremely hot and can cause burns. 

Before performing any service/maintenance on 
the paver, always disconnect the battery to 
prevent unintentional starting. 

Do not attempt to remove the radiator cap after 
the engine has reached operating temperature 
or if it is overheated. At operating 
temperatures, engine coolant is extremely hot 
and under pressure. Always wait for the engine 
to cool before attempting to relieve pressure 
and remove the radiator cap. Failure to heed 
this warning could result in severe burns. 

Dispose of all petroleum-based oils and fluids 
properly. Used motor oil may pose a health 
risk. Wipe oil from your hands promptly and 
wash off any residue. Used motor oil is an 
environmental contaminant and may only be 
disposed of at approved collection facilities. 
Never drain any petroleum-based product on 
the ground, dispose of in municipal waste 
collection containers, or in metropolitan sewer 
systems or landfills. Check state and local 
regulations for other requirements.

Screed Propane Heater Safety 
Reminders

WARNING

Do not smoke in the area around a paver 
equipped with propane burners. 

ALWAYS be sure a suitable fire extinguisher is 
readily available. 

ALWAYS light ignitor with a striker. NEVER use 
a cigarette lighter or a match. 

Ignitor flame may be invisible in sunlight. Do 
not place ignitor near your skin or clothing. 
Severe burns will result.

ALWAYS allow the screed to cool before lower-
ing it for transport. Fires could result.

Only use propane gas with the screed propane 
heater.

Wrench-tighten all fittings.

Never use oil or grease for lubrication.

Keep the propane supply cylinder upright at all 
times.

Keep the paver free of dirt and oil.

Use a regulator valve on the propane supply 
cylinder.

Check the screed propane heater equipment 
carefully each time before lighting.

Do not operate the screed propane heater in an 
enclosed area or near flammable material. 

Close all valves when not in use. 

Comply with all federal, state and local 
regulations during operation. 

Courtesy of Machine.Market 

Содержание 1448 Plus





















































































Отзывы: