Gehl 1448 Plus Скачать руководство пользователя страница 31

Страница: 31 / 84

Printed in U.S.A

918215/CP0407

1448 PLUS

INDICATORS AND CONTROLS

Washdown Sprayer System

(Items 20 & 21, Fig. 3)

The washdown sprayer system is used periodically
each day to wash down parts of the paver with an
asphalt releasing agent.

IMPORTANT:

Use only releasing agents

approved for use according to environmental
regulations applicable to the area of paver
operation.

WARNING

Do NOT spray releasing agent on a hot engine.

Hydraulic Fluid Reservoir Fill

(Item 22, Fig. 3)

Remove the hydraulic reservoir fill plug to check
the hydraulic fluid level or to add hydraulic fluid.

NOTE:

Before removing the hydraulic

reservoir fill plug (H), allow the fluid to cool
for 10-15 minutes. Slowly loosen the breather
cap on the backwall top console to release
system pressure (shown in “Change Hydraulic
Filter” on page 59).

Paving Alignment Guide

(Item 23, Fig. 3)

The adjustable paving alignment guide (I) is used
to align the paver with a curb or the edge of a
previously laid mat of asphalt.

Fig. 13 - Washdown Fill and Spray Nozzle

Washdown

Reservoir Fill

and Switch

Washdown

Spray

Nozzle

Fig. 14 - Hydraulic Fluid Reservoir Fill

Fig. 15 - Paving Alignment Guide

Courtesy of Machine.Market

Содержание 1448 Plus





















































































Результаты поиска

Содержание 1448 Plus

Отзывы:

Похожие инструкции для 1448 Plus

Бренды по названию

Популярные бренды

Gehl 1448 Plus, Руководство оператора

Результаты поиска

Содержание 1448 Plus

Отзывы:

Похожие инструкции для 1448 Plus

Бренды по названию

Популярные бренды