Gehl 1448 Plus Скачать руководство пользователя

Страница: 63 / 84

Printed in U.S.A

918215/CP0407

1448 PLUS

SERVICE AND STORAGE

Change Hydraulic Filter

1. Perform the Mandatory Safety Shutdown

procedure on page 15.

WARNING

Hydraulic fluid is hot during operation. Allow
the hydraulic system to cool before relieving
system pressure by loosening breather cap on
top of the backwall.

2. Loosen the hydraulic breather cap (1, Fig. 38)

to relieve hydraulic system pressure.

Fig. 38 - Hydraulic System Breather Cap

3. Unscrew and remove the hydraulic filter

element (2, Fig. 39) and discard.

Fig. 39 - Hydraulic Filter Components

4. Wipe the sealing surface on the mounting head

(3) with a clean cloth.

5. Apply a thin coat of clean oil to the new oil

filter gasket.

6. Install a new hydraulic filter element (2) on the

filter head and hand-tighten.

Change Engine Oil and Filter

Replace the engine oil filter when changing the
engine oil.

1. Run the engine until it reaches operating

temperature.

2. Perform the Mandatory Safety Shutdown

Procedure on page 15.

3. Prepare a waste oil container to collect the

engine oil as it drains.

4. Remove the engine crankcase drain plug.

Allow the oil to drain into the waste oil
container.

IMPORTANT:

DO NOT discharge engine oil

onto the ground. Contain and dispose of
engine oil according to environmental laws
and waste regulations.

5. Remove all metallic filings from the drain

plug. Re-install and tighten the drain plug.

6. Remove and discard the engine oil filter

(1, Fig. 40).

Fig. 40 - Engine Oil Filter

7. Wipe the oil filter gasket sealing area on the

engine block with a clean cloth.

Courtesy of Machine.Market

Содержание 1448 Plus





















































































Результаты поиска

Содержание 1448 Plus

Отзывы:

Похожие инструкции для 1448 Plus

Бренды по названию

Популярные бренды

Gehl 1448 Plus, Руководство оператора

Результаты поиска

Содержание 1448 Plus

Отзывы:

Похожие инструкции для 1448 Plus

Бренды по названию

Популярные бренды