manualshive.com logo in svg

gefran 2850T, Инструкция по использованию и установке, Страница: 21 / 166

Поделиться
Скачать
gefran 2850T Скачать руководство пользователя страница 21

19

2. INSTALLATION

80703B_MHW_2850T/3850T_02-2019_ENG

2.  INSTALLATION

Warning!

 The installation of the devices described in the manual must be carried out by qualified personnel, fol-

lowing the laws and regulations and in accordance with the instructions contained in this manual.

Before proceeding with the installation, check that the controller is intact and has not been damaged during trans-
port. Also make sure that the package contains all the accessories listed in the supplied documentation, especially 
the sealing gasket and fixing brackets.

Verify that the order code corresponds to the configuration required for the application in which the controller is 
intended (the supply voltage, number and type of inputs and outputs). See chapter 10 - Order codes - to verify the 
configuration corresponding to each order code.

Warning!

 If even one of the above-mentioned requirements (qualified technician, device intact, configuration not 

matching that required) is not met, suspend installation and contact your Gefran dealer or Gefran Customer Ser-
vice.

2.1.  Controller assembly

2.1.1.  General installation rules

The controller is designed for permanent indoor instal-
lations. It must be mounted in electrical cabinets, or in 
machine or production process plant control panels, which 
are able to protect the connectors on the back of the con-
trollers.

Warning! 

The controller must NOT be installed in 

dangerous environments (flammable or explosive). 
It can be connected to elements that operate in 
such environments only by means of suitable 
types of interfaces in conformity with the applica-
ble safety standards.

Warning!

 If the controller is used in applications 

with risk of damage to persons or property, it is 
essential to combine it with specific alarm devic-
es. We recommend including the ability to check 
alarm operation even during the normal operation 
of the controller and the system or equipment 
being monitored.

Sudden changes in temperature, freezing or condensation 
or corrosive gases should not occur where the controller is 
installed.

The controller can operate in environments with pollution 
degree 2 (presence of non-conductive dust, only temporar-
ily conductive due to potential condensation). Prevent the 
device from being reached by metallic processing particles 
or scraps as well as any condensation products.

The controller is sensitive to strong electromagnetic fields. 
Avoid placing it near radio devices or other equipment that 
can generate electromagnetic fields, such as high-pow-
er remote controllers, contactors, relays, thyristor power 
groups (in particular, phase shift), motors, solenoids, trans-
formers, high-frequency welders, etc.

2.1.2.  Drilling Dimensions

For proper interface installation, respect the size of the sin-
gle hole and the spacing between the adjacent holes shown 
in the illustrations of the different models (“Figure 2 - 2850T 
interface dimensions and drilling templates” on page 13 
and “Figure 4 - 3850T interface dimensions and drilling 
templates” on page 15).

Warning!

 The support on which the interface must 

be mounted must have the following characteris-
tics:
• 

be rigid and sturdy enough to support the 
device and not bend during use;

• 

have a thickness between 1 and 4 mm, in 
order to allow the device to be secured with 
the supplied brackets.

2.1.3.  Protection against dust and water 
infiltration

The front of the interface provides IP65 protection. There-
fore, the device can be installed in dusty environments or 
subject to water sprays provided that:
• 

the compartment containing the interface is also dust 
and water-tight;

• 

the support on which the interface is installed is per-
fectly smooth and without undulations in the front;

• 

the hole on the support scrupulously complies with the 
indicated drilling dimensions;

• 

the interface well-secured to the support, to enable 
the gasket inserted between the device and panel to 
ensure water-tightness.

Warning! 

If not adequately protected, the inter-

face protection degree is IP20 (rear housing and 
connectors).

Содержание 2850T







































































































































































Отзывы:

Нет отзывов