Gechter 2,5 HKPE Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 60

Gechter 2,5 HKPE Скачать руководство пользователя страница 9

General Information

2

Hand toggle presses

–

Translation of the original operating manual

4

Definition according to DIN EN 60204-1:

Trained personnel:

A person who has been instructed and trained where necessary by an expert
regarding the tasks to be transfered as well as the possible dangers in the
event of improper behavior and who has been instructed on the necessary pro-
tective equipment and protective measures.

Technically trained personnel:

A person whose professional training, knowledge and experience as well as
knowledge of relevant standards allows him/her to assess the assigned work
and detect possible dangers.

Qualification of the operating personnel:

Work may only be carried out on the machine independently by people who



have been instructed and trained on the system by expert or service

personnel of Gechter GmbH Werkzeug- und Maschinenbau and who
are therefore familiar with the technology



are physically and mentally capable to do so

Outside of the Federal Republic of Germany, the applicable accident prevention
regulations, safety provisions and youth employment protection laws of the re-
spective country shall apply.

2.3

Objectives of the operating manual

This operating manual is intended as an aid and contains all necessary infor-
mation that must be taken into consideration for the general safety, transport,
installation, operation, maintenance and setup.

This operating manual with all of the safety instructions (as well as all addi-
tional documents of the modules from third party suppliers) must:



be observed, read and understood by all people who work on the

press (especially knowledge of the safety instructions)



be freely accessible to everyone



be consulted in cases of even the slightest doubt (safety)

Goals:



Avoid accidents



Increase the service life and reliability of the press



Reduce production downtime costs

«
...
7
8
9
10
11
...
»

Содержание 2,5 HKPE





























































Отзывы:

Нет отзывов