Gechter 2,5 HKPE Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 60

Gechter 2,5 HKPE Скачать руководство пользователя страница 10

General Safety Instructions

3

Hand toggle presses

–

Translation of the original operating manual

5

3.

General Safety Instructions

3.1

Scope and Symbols

Danger to life, risk of injury and cause of physical damage

Failure to observe the operating manual and all of the safety in-
structions contained therein may result in dangers.

Carefully read the operating manual prior to the initial commis-
sioning. Meet the required safety conditions prior to the initial
commissioning.

General safety instructions and also the special safety instruc-
tions inserted in other chapters are to be observed.

The machine is built in keeping with the latest technological developments and
according to the recognized technical safety rules. In order to exclude dangers
to the life and limb of the user, third parties or other damage during its use,
only use the press for the intended use and in the clearly technically safe and
perfect condition.

Property damage and physical injuries that are due to the instructions in the
operating manual being ignored are the responsibility of the press operator of
the persons commissioned by said operator.
Faults that may impair the safety must be rectified immediately.
All safety and hazard information about the press is to be observed and con-
stantly kept in a good legible condition.

3.1.1

Safety symbols

–

pursuant to DIN 4844-2

Risk of injury from ignoring the safety symbols

Dangers arise from ignoring the warning information about the
press and in the operating manual.

Observe the warning information in the "Appendix" chapter.

«
...
8
9
10
11
12
...
»

Содержание 2,5 HKPE





























































Отзывы:

Нет отзывов