Gechter 2,5 HKPE Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 60

Gechter 2,5 HKPE Скачать руководство пользователя страница 50

Service and maintenance

9

Hand toggle presses

–

Translation of the original operating manual

45

9.2.1

Cleaning the press

Risk of explosion from flammable cleaning agents!

There  is  a  risk  of  explosion  if  benzine  is  used  for  cleaning.  It  is
highly  flammable,  electrostatically  chargeable  and  can  produce
an explosive gas-air mixture.

Use halogen-free cold cleaners with a high flash point for clean-
ing.

Danger of injury from ignoring the manufacturer's specifi-
cations!

The press function may be impaired if the manufacturer's clean-
ing instructions are ignored.

Comply with all environmental protection regulations during
cleaning.

Dust and heat leave residues on the press components an can cause functional
disruptions.

Do not use any sharp tools for cleaning as they can damage the paint and thus
cause corrosion.

Proceed as follows when cleaning the outside of the press:



Only perform cleaning work with cloths, brushes and vacuum cleaners!



Remove all aids after the cleaning is complete!



Check the function of the cleaned area!

«
...
48
49
50
51
52
...
»

Содержание 2,5 HKPE





























































Отзывы:

Нет отзывов