Gechter 2,5 HKPE Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 60

Gechter 2,5 HKPE Скачать руководство пользователя страница 8

General Information

2

Hand toggle presses

–

Translation of the original operating manual

3

2.

General Information

2.1

Warranty and liability

In general, the "General terms and conditions of sale and delivery" of the
company Gechter GmbH Werkzeug- und Maschinenbau shall apply. These are
available to the operator at the latest upon contract conclusion.

Warranty and liability claims in the event of personal injury or property dam-
age are excluded if they are due to one or more of the following reasons:



improper use of the press



improper assembly, commissioning, operation and maintenance



operating the press with defective safety devices



disregarding instructions in the operating manual



unauthorized structural changes



deficient maintenance, repair and service measures



cases of disaster caused by foreign bodies or force majeure

2.2

Target group of the operating manual

Target Group

The operating manual is intended for the operator and personnel with the fol-
lowing areas of expertise:

Work area

Expertise

Installation, transport and storage

Technically trained personnel

Commissioning, operation and decommissioning

Trained personnel

Setup

Technically trained personnel

Service and maintenance

Technically trained personnel

Troubleshooting

Technically trained personnel

«
...
6
7
8
9
10
...
»

Содержание 2,5 HKPE





























































Отзывы:

Нет отзывов