Gechter 2,5 HKPE Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 60

Gechter 2,5 HKPE Скачать руководство пользователя страница 33

Commissioning / Operation

6

Hand toggle presses

–

Translation of the original operating manual

28

6.

Commissioning / Operation

Observe the safety chapter

The basic safety information for the press is located in the "Safe-
ty Information" chapter.

6.1

Commissioning



Check the press and all associated mechanical components for damage!

Risk of injury from damage and defects

Specify the responsibility of the commissioning personnel.
Before  commissioning, check  the  press  to  ensure  it has  the  cor-
rect  setting  and  ensure  the  presence  of  the  required  protective
and  safety  devices.  If  defects  are  identified,  stop  the  press  until
these defects are rectified.

Immediately  replace  defective  press  components.  Use  the  addi-
tional documents in the appendix of this operating manual to en-
sure an undoubted identification of the component.

6.1.1

Functional check before operation

Risk of injury from damage and defects

There is a danger from damage and defects on the press.

Do not operate the press in the case of localized and identified
damage. Replace defective components.

«
...
31
32
33
34
35
...
»

Содержание 2,5 HKPE





























































Отзывы:

Нет отзывов