Gechter 2,5 HKPE Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 60

Gechter 2,5 HKPE Скачать руководство пользователя страница 58

Spare parts and ordering

11

Hand toggle presses

–

Translation of the original operating manual

53

11.

Spare parts and ordering

11.1

Spare parts



Only use spare parts and other parts from the system manufacturer
Gechter GmbH!

See the spare parts drawings and parts lists for additional infor-
mation!
The spare parts drawings and parts lists can be viewed or downloaded
at www.gechter.com in the download area.

Note

In general, the "General terms and conditions of sale and deliv-
ery" of Gechter GmbH shall apply. These are available to the op-
erator at the latest upon contract conclusion. You confirm the
order with your signature!

11.2

Order



Contact the following address when ordering spare parts:

Gechter GmbH Werkzeug- und Maschinenbau
Ostring 3
90587 Obermichelbach

GERMANY

Tele-
phone:

0911 / 982873-20

Fax:

0911 / 982873-99

E-mail:

[email protected]

The following information is required when ordering:



Press type



Press number



Year of manufacture

«
...
56
57
58
59
60
»

Содержание 2,5 HKPE





























































Отзывы:

Нет отзывов