GEA ECOVENT Скачать руководство пользователя страница 81

Страница: 81 / 128

For optional version with proximity
switch holder (C):

5.1

Screw the mounting for the
proximity switch (C) into the ac-
tuator using the jaw wrench on
the wrench flat surface (C3).

5.2

Screw the switch bar (139) into
the  mounting  for  proximity
switch  (C)  on  the  wrench  flat
surface  (139.1)  using  a  jaw
wrench (a/f 17).

Observe torques, see table ‘Tighten-

ing torques’.

9.6.1 Tightening tor-

ques

139

139.1

Press the bearing (2) into the lantern
(9).

Place the seal disk (3) with the O-ring
(5) and seal ring (1) into the housing.

Place the lantern (9) onto the housing
and mount the hinged clamp (43) be-
tween the housing and the lantern.

Observe torques, see table ‘Tight-

ening torques’.

9.6.1 Tightening

torques

Place the seat ring (33) with the O-
ring (5) into the housing.

10.

Screw  valve  disk  (15)  with  the  V-ring
(7)  into  actuator  and  tighten  using
jaw  wrench  at  wrench  flat  surface
(15.1).  To  do  this,  affix  with  a  belt
wrench.

Observe torques, see table ‘Tight-

ening torques’.

9.6.1 Tightening

torques

5
5

15.1

The valve insert is assembled from individual parts.

9.6 Installing the valve - 81 / 128

Содержание ECOVENT
































































































































Результаты поиска

Содержание ECOVENT

Отзывы:

Похожие инструкции для ECOVENT

Бренды по названию

Популярные бренды

GEA ECOVENT, Руководство по эксплуатации

Результаты поиска

Содержание ECOVENT

Отзывы:

Похожие инструкции для ECOVENT

Бренды по названию

Популярные бренды