GEA ECOVENT Скачать руководство пользователя страница 107

Страница: 107 / 128

11 Decommissioning, dismantling and

disposal

This chapter contains information about decommissioning the valve. It also describes

the removal and disposal processes. It is addressed to all persons who carry out actions

related to the valve.

INFO

During all decommissioning, observe the chapter

2 Safety

of this Operating

Instructions.

11.1 Decommissioning

The following principles apply for decommissioning:

●

Switch off the compressed air.

●

Switch off the component with the main switch.

●

Padlock the main switch (if fitted) in the off position to prevent it from being switch-

ed back on. The key to the padlock must be deposited with the person responsible

until the machine is restarted.

●

For longer periods of standstill, observe the storage conditions, see

4.2 Storage

11.2 Dismantling

Prerequisites

●

Ensure that no active processes are running in the relevant area during disman-

tling.

Empty all pipe elements that lead to the valve.

Shut off the control air supply.

Disconnect the power supply.

Take the valve out of the pipe section, with all housings and housing connections if
possible.

The valve has been dismantled.

11.3 Disposal

Dispose of the valve in an environmentally friendly manner. Observe the statutory waste

disposal regulations applicable at the place of installation.

The valve is made of the following materials:

●

Metals

●

Synthetic materials

●

Electronic parts

●

Lubricants containing oil and grease

Separate the different materials and dispose of them correctly sorted. Also observe the

instructions regarding disposal in the instruction manual for the individual components.

11.1 Decommissioning - 107 / 128

Содержание ECOVENT
































































































































Результаты поиска

Содержание ECOVENT

Отзывы:

Похожие инструкции для ECOVENT

Бренды по названию

Популярные бренды

GEA ECOVENT, Руководство по эксплуатации

Результаты поиска

Содержание ECOVENT

Отзывы:

Похожие инструкции для ECOVENT

Бренды по названию

Популярные бренды