GEA ECOVENT Скачать руководство пользователя страница 30

Страница: 30 / 128

3.2.3 Resistance and permitted operating temperature of the

sealing materials

The resistance and permitted operating temperature of the sealing materials depend on

the type and temperature of the medium conveyed. The exposure time can adversely

affect the service life of the seals. The sealing materials comply with the regulations of

FDA 21 CFR 177.2600 or FDA 21 CFR 177.1550.
The maximum operating temperature is defined by the sealing type and its mechanical

load.
Due to the versatile conditions of use (e.g. usage duration, switching frequency, type

and temperature of product and cleaning agents as well as usage environment), GEA

Tuchenhagen recommends that the user carries out resistance tests.
Resistance:

●

+ = good resistance

●

o = reduced resistance

●

– = no resistance

Medium

Maximum operating temper-
atures

EPDM

FKM

HNBR

Alkalis up to 3%

up to 80 °C (176°F)

Alkalis up to 5%

up to 40 °C (104°F)

Alkalis more than 5%

up to 80 °C (176°F)

–

Alkalis more than 5%

–

Inorganic acids up to 3%

up to 80 °C (176°F)

Inorganic acids up to 5%

up to 80 °C (176°F)

Inorganic acids up to 5%

up to 100 °C (212°F)

–

Water

up to 100 °C (176°F)

Steam

up to 135 °C (275°F)

Steam, approx. 30 min

up to 150 °C (302°F)

Fuels/hydrocarbons

Product with a fat content of max. 35%

Product with a fat content of more than 35%

Oils

30 / 128 - 3.2 Technical data

0000000607 - 002 - EN-GB

Содержание ECOVENT
































































































































Результаты поиска

Содержание ECOVENT

Отзывы:

Похожие инструкции для ECOVENT

Бренды по названию

Популярные бренды

GEA ECOVENT, Руководство по эксплуатации

Результаты поиска

Содержание ECOVENT

Отзывы:

Похожие инструкции для ECOVENT

Бренды по названию

Популярные бренды