manualshive.com logo in svg

GE Profile PFCF1RKZ, Техническое обслуживание руководство

Поделиться
Скачать
GE Profile PFCF1RKZ Скачать руководство пользователя страница 59

– 59 –

Inverter Compressor

Caution:

 Do not attempt to direct-start the 

compressor. The compressor operates on a 3-phase 
power supply. Applying 120 VAC to the compressor 
will permanently damage the unit. It is not possible 
to start the compressor without an inverter.

The compressor is a reciprocating, variable-speed, 
4-pole type. It operates on 3-phase, 80 to 240 VAC 
within a range of 57 to 104 Hz.  

Note:

 Certain voltmeters will not be able to read 

voltage output or frequency from the inverter.

Compressor wattages at various speeds are: 

•  LOW - 65 watts 

•  MED - 100 watts

•  HIGH - 150 watts

The compressor is controlled by the inverter, which 
receives its signal from the main control board. 
Varying the frequency to the inverter changes the 
compressor speed.

Compressor speed is based on the temperature 
set point in conjunction with the speci

fi

 c cabinet 

temperature. Speeds are selected according to 
the following cabinet temperatures, with freezer 
temperature being the primary:
•   7°F to 19.5°F above freezer set point = high 

speed.

•   4.5°F to 6.5°F above freezer set point = medium 

speed.

•   1°F to 4°F above freezer set point = low speed.
•  1°F to 2.5°F above refrigerator set point = low 

speed.

ORANGE

ORANGE

NEUTRAL OUTPUT

NEUTRAL INPUT

AC

ORANGE

BL

AC

K

BLUE

BROWN

BROWN

BROWN

WHITE

RED

LINE OUTPUT

LINE INPUT

INVERTER

RED

WHITE

J15-1

J15-2

10

EMI

FILTER

FERRITE BEAD

FERRITE BEAD

MAIN CONTROL BOARD

10

10

• 

3°F to 5°F above refrigerator set point - medium 
speed.

•  5.5°F to 7°F above refrigerator set point - high 

speed.

Note:

 The compressor will run at medium speed if 

the freezer temperature is 20°F or more above the 
setpoint.  
The use of 3-phase power eliminates the need for 
the relay, capacitor, and individual start and run 
windings; therefore, the start, run, and common 
pins found on conventional compressors are not 
applicable on this 3-phase model. Compressor pin 
functions are identical and compressor lead wire 
con

fi

 guration is of no importance.  A resistance of 

9 

 to 11 



should be read between any 2 of the 

3 pins. Should an opening occur in the compressor 
winding or should one of the compressor lead wires 
become open or disconnected, the inverter will stop 
voltage output to the compressor. 

Compressor operation is extremely smooth and 
cool. The compressor exterior may be slightly higher 
than room temperature while operating; therefore, it 
may be dif

fi

 cult to detect a running unit. 

To verify that the compressor is running:

Disconnect power from the unit and place a hand 
on the compressor. Reconnect power and feel for 
a vibration when the compressor tries to start. It 
may take up to 8 seconds before the compressor 
attempts to start.

Note:

•  When ordering a replacement compressor, 

order both the compressor and inverter. Replace 
the compressor 

fi

 rst. If the compressor fails to 

start after compressor installation, replace the 
inverter.

•  When servicing the compressor, it is important 

to dress the wiring to keep low voltage DC wiring 
and 120 VAC wiring separate.

Содержание Profile PFCF1RKZ



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды