GE Profile PFCF1RKZ Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 66

– 10 –

Door Alarm

The door alarm will sound and the door alarm LED
will be

fl

ashing if any door/drawer is open for more

than 2 minutes. When you close the door/drawer,
the beeping stops and the LED will reset to full on.

Dispenser Light

This pad turns the night light in the dispenser on
and off. The light also comes on when the dispenser
cradle is pressed.

Note:

• The refrigerator temperature cannot be

changed during TurboCool.

• The freezer temperature is not affected and can

be changed during TurboCool.

• When opening the refrigerator door during

TurboCool, the fans will continue to run if they
have cycled on.

TurboCool

TM

How it Works

TurboCool™ rapidly cools the refrigerator
compartment in order to more quickly cool foods.
Use TurboCool when adding a large amount of food
to the refrigerator compartment, putting away
foods after they have been sitting out at room
temperature, or when putting away warm leftovers.
It can also be used if the refrigerator has been
without power for an extended period.

Once activated, the compressor will turn on
immediately and the fans will cycle on and
off at high speed as needed for 8 hours. The
compressor will continue to run until the refrigerator
compartment cools to approximately 34°F, then it
will cycle on and off to maintain this setting. After
8 hours, or if

T

URBO

C

OOL

is pressed again, the

refrigerator compartment will return to the original
setting.

How to Use

Press the

T

URBO

C

OOL

pad. The refrigerator

temperature display will show .

After TurboCool is complete, the refrigerator
compartment will return to the original setting.

Door Alarm LED

Energy Saver LED

Dispenser Light LED

TurboCool LED

(

Continued next page

)

Energy Saver (If Available)

Some products are equipped with an energy saver
pad and LED. The refrigerator is shipped with the
energy saver feature enabled.

Over time, moisture can form on the front surface of
the refrigerator cabinet and cause rust. If moisture
does appear on the front surface of the refrigerator
cabinet, turn off the energy saver feature (if
available) by pressing and releasing the

E

NERGY

S

AVER

pad on the control panel.

«
...
8
9
10
11
12
...
»

Содержание Profile PFCF1RKZ



































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды