manualshive.com logo in svg

GE Profile PFCF1RKZ, Техническое обслуживание руководство

Поделиться
Скачать
GE Profile PFCF1RKZ Скачать руководство пользователя страница 42

– 42 –

Fan Cover

8. Remove 

the 

fi

 ve 1/4-in. Hex-head screws that 

attach each lower rail assembly to the freezer 
wall.

9.  Pull the front of the rail assembly towards the 

center of the freezer and unhook the assembly 
from the side of the freezer.

10.  Remove the 1/4-in. hex-head screw and the fan 

cover from the evaporator cover.

6.  Remove small black locating pin from the roller  

guide bar.

Note:

 For best results when re-installing the roller 

guide bar, start with rollers in rear location.

7.  Slide the roller guide bar to right and remove it 

from the rollers. 

Bottom Tab

Bottom Tab

Bottom Tab

Note:

 The evaporator cover is attached to the 

evaporator compartment with 3 recessed  1/4-in. 
hex-head screws, 3 bottom tabs, and 5 snap tabs 
located on the back of the cover. 

11.  Remove the three 1/4-in. hex-head screws that 

attach the evaporator cover.

12.  Grasp the right side of the fan opening and pull 

the cover towards the front of the freezer to 
release the right side snap tabs.

13.  Reach in and disconnect the evaporator fan 

motor wire harness, and then remove the cover 
from the freezer.

Disconnect

Содержание Profile PFCF1RKZ



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды