GE Profile PFCF1RKZ Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 66

– 43 –

(

Continued next page

)

Evaporator Fan

The position of the fan blade in relation to the
shroud is important.

5/16" ± 0.03

Blade tip

1.0" ± 0.05 Target

Motor

Air Flow

Orifice

The evaporator fan is the same fan used on previous
models; however, a signi

fi

cant difference is that the

main control board neither requires nor receives
input from the fan feedback/rpm (blue) wire. The fan
utilizes a permanent magnet, 4-pole, DC motor that
operates at 3 different speeds: high, medium, and
low.
Supply voltage from the main control board (J2-8 to
J2-3) remains at a constant 13.6 VDC.
The speed of the fan is controlled by the signal
voltage output from the main control board (J2-4 to
J2-3). Voltage output from the main control board to
the fan is 13.6 VDC; however, to regulate the speed
of the fan, the main control board uses pulse width
modulation (PWM).

When operating, voltage is sent in pulses (much like
a duty cycle) as opposed to an uninterrupted

fl

ow.

This pulsing of 13.6 VDC produces effective voltage
being received at the motor, that is equivalent to a
reduction in voltage.

High Speed (9.5 VDC measured)

Medium Speed (8 VDC measured)

Low Speed (6.5 VDC measured)

12.3 VDC

11.5 VDC

8.2 VDC

13.6 VDC

0 VDC

0 VDC

0 VDC

13.6 VDC

13.6 VDC

Note:

Depending on speed, the effective voltage

may range from 6.5 - 13.6 VDC.

Fan speed is selected and maintained by the main
control board regulating the length and frequency
of the 13.6 VDC pulse. Temperature can cause
some fan speed variation. Fan speed can vary +/-
5%, depending on the temperature, with higher
temperatures causing slightly higher speeds.

The evaporator fan has a 4-wire connection:

White Wire

- DC Common (J2 pin 3)

The white wire is the DC common wire used
for testing. During repairs, DC polarity must be
observed. Reversing the DC polarity causes a
shorted motor and/or board.

Red Wire

- Supply (J2 pin 8)

Each motor uses an internal electronic controller to
operate the motor. Supply voltage from the main
control board remains at a constant 13.6 VDC.

Blue Wire

- Feedback/RPM (J2 pin 1)

On previous Arctica models, the blue wire reported
rpm (speed) information to the main control board
for speed control purposes. On this model, the board
does not require or read any feedback information
from the fan motor.

Yellow Wire

- Signal (J2 pin 4)

The yellow wire is the input wire from the main
control board. The main control board provides
8.2 VDC effective voltage for low speed, 11.5 VDC
effective voltage for medium speed, and 12.3 VDC
effective voltage for high speed. The fan operates
in low speed only when the fresh food thermistor is
satis

fi

ed.

«
...
41
42
43
44
45
...
»

Содержание Profile PFCF1RKZ



































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PFCF1RKZ

CoolMatic CRX50

Бренд: Waeco Страницы: 380

Бренд: Waeco Страницы: 300

Бренд: U-Line Страницы: 16

Бренд: GE Страницы: 136

Бренд: Oypla Страницы: 7

Бренд: Sauber Страницы: 20

Бренд: Tesla Страницы: 88

Бренд: Engel Страницы: 20

HSM25GFRESA and

Бренд: Hotpoint Страницы: 88

Бренд: inventum Страницы: 60

Бренд: Amica Страницы: 60

Бренд: Magic Chef Страницы: 5

Бренд: Accucold Страницы: 16

Бренд: Fagor Страницы: 84

MASTERCHEF EXECUTIVE PSC-WG-1020

Бренд: Sam Cook Страницы: 32

GSC22KGRCBB and

Бренд: GE Страницы: 124

Monogram ZIF360NHXH

Бренд: GE Страницы: 20

Monogram ZIC360NRGLH

Бренд: GE Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды