GE Profile PFCF1RKZ Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 66

– 53 –

Note:

If the Energy Saver light (if available) is on,

then the articulating door mullion heater is disabled.

The heater operates on DC voltage when both
doors are closed. It is necessary to close the right
side door and close the left side light switch to test
for the operating voltage of 0 to 13.6 VDC. (See

Mullion Heaters

.) The resistance of the heater is

approximately 24

Ω

.

To replace the articulating door mullion assembly,
remove the 2 Phillips-head screws from the top
and bottom hinges. The wire harness can be pulled
out from the recess in the bottom of the door and
disconnected.

Top Hinge

Bottom Hinge

Wire

Harness

4. Separate the mullion face from the refrigerator

cabinet.

5. Disconnect the mullion face wire harness and

ground wire.

Wire Harness

Ground

Wire

(

Continued next page

)

Double Drawer Mullion Assembly

The double drawer mullion assembly consists of a
mullion heater bonded to a mullion face. The mullion
face is attached to the mullion with 4 Phillips-head
screws. The mullion is inserted in 2 recesses and
attached to the freezer walls with four 3/16-in. Allen-
head shoulder bolts.

To remove the double drawer mullion assembly:

1. Unplug the refrigerator.

2. Remove the top and bottom freezer drawers.

(See

Top Freezer Drawer, Bottom Freezer Drawer

.)

3. Remove the 4 Phillips-head screws that attach

the mullion face to the mullion.

«
...
51
52
53
54
55
...
»

Содержание Profile PFCF1RKZ



































































Отзывы:

Нет отзывов