GE Profile PFCF1RKZ Скачать руководство пользователя страница 41

Страница: 41 / 66

– 41 –

Evaporator Thermistor

The evaporator thermistor is clipped to the suction
tube line of the evaporator. (See

Evaporator

for

accessing instructions.)

Evaporator Thermistor

(

Continued next page

)

Silicone Grease

Note:

When replacing the evaporator thermistor,

splice a new thermistor into the harness using
connectors and procedures approved for damp/wet
conditions.

Evaporator

The following components must be removed in the
appropriate order to access the evaporator:

1. Unplug the refrigerator.

2. Remove the upper and lower freezer drawers.

(See

Top Freezer Drawer

Bottom Freezer Drawer

Note:

• For added accessibility to freezer components,

it may be necessary to remove the double
drawers mullion assembly. (See

Double Drawer

Mullion Assembly

• Each upper drawer side rail assembly is held

in place by four 1/4-in. hex-head screws and a
hook that locks into an opening in the side of the
freezer.

3. Extend both upper drawer rail assemblies to the

open position.

4. Remove the four 1/4-in. hex-head screws that

attach each upper rail assembly to the freezer
wall.

5. Pull the front of the rail assembly towards the

center of the freezer and unhook the assembly
from the side of the freezer.

Содержание Profile PFCF1RKZ



































































Результаты поиска

Содержание Profile PFCF1RKZ

Отзывы:

Похожие инструкции для Profile PFCF1RKZ

Бренды по названию

Популярные бренды

GE Profile PFCF1RKZ, Техническое обслуживание руководство

Результаты поиска

Содержание Profile PFCF1RKZ

Отзывы:

Похожие инструкции для Profile PFCF1RKZ

Бренды по названию

Популярные бренды