GE Profile PFCF1RKZ Скачать руководство пользователя страница 54

Страница: 54 / 66

– 54 –

EMI Filter

The EMI Filter is accessed from the back of the

refrigerator and is located on the left side of the
compressor.

To remove the EMI fi lter:

1. Remove the 5/16-in. hex-head screw that

attaches the bracket to the cabinet.

2. Pull the bracket out and remove the 1/2-in. nut.

3. Cut the 2 plastic wire ties that hold the EMI

lter

to the bracket.

4. Mark and disconnect the wires from the EMI

lter.

5/16-in.Screw

1/2-in. Nut

Wire Tie

6. Remove the four 3/16-in. Allen-head shoulder

bolts (2 on each side) that attach the mullion to
the freezer walls.

7. Pull out the mullion from the recesses (1 on

each side) in the freezer walls.

8. Disconnect the mullion wire harness.

Wire

Harness

Fresh Food/Freezer Mullion Heater

The fresh food/freezer mullion heater is foamed in
place and is located behind the cabinet

ange and

between the freezer and fresh food compartments.

Note:

If the Energy Saver light (if available) is

on, then the fresh food/freezer mullion heater is
disabled.

The heater is not replaceable.

Note:

To test the operation of the mullion heater,

disconnect the humidity sensor. Within the next 20
minutes (duty cycle), the control will recognize the
open humidity sensor, the heater will then receive
voltage, and the mullion will get warm.

Содержание Profile PFCF1RKZ



































































Результаты поиска

Содержание Profile PFCF1RKZ

Отзывы:

Бренды по названию

Популярные бренды

GE Profile PFCF1RKZ, Техническое обслуживание руководство

Результаты поиска

Содержание Profile PFCF1RKZ

Отзывы:

Бренды по названию

Популярные бренды