Setpoints, Pg. 2
3 SETUP AND USE
Page
Line
Information Line
Setpoint Range and Units
Manual Ref.
3-21
2
1
PAGE 2: SETPOINT VALUES
PAGE 2: SETPOINT VALUES
RTD SETPOINTS
RTD SETPOINTS
2
RTD SENSOR TYPE
RTD SENSOR TYPE
TYPE = 100 OHM PLATINUM
TYPE = 100 OHM PLATINUM
Not a setpoint.
Displays the RTD type the relay
will accept. To change the RTD
type, contact the factory.
100 ohm platinum, 10 ohm cop-
per, 100 ohm nickel, 120 ohm
nickel.
3.16
3
ARE THERE ANY RTDs
ARE THERE ANY RTDs
CONNECTED? XXX
CONNECTED? XXX
YES or NO
When programmed to “NO”, all
RTD messages in Setpoints and
Actual Values are not displayed.
Factory Value = YES
3.16
4
RTD MESSAGE DISPLAY = C
RTD MESSAGE DISPLAY = C
(C:CELSIUS/F:FAHRENHEIT)
(C:CELSIUS/F:FAHRENHEIT)
C or F
Factory Value = C
3.16
5
# OF STATOR RTDS USED
# OF STATOR RTDS USED
# OF RTDs = X
# OF RTDs = X
0-6 (increments of 1)
Factory Value = 6
3.16
6
STATOR #1 ALARM LEVEL
STATOR #1 ALARM LEVEL
= XXX DEGREES C
= XXX DEGREES C
or
RTD #1 ALARM LEVEL
RTD #1 ALARM LEVEL
= XXX DEGREES C
= XXX DEGREES C
0-200 degrees C or OFF
(increments of 1)
(32-392 degrees F)
Factory Value = OFF
3.16
7
STATOR #1 TRIP LEVEL
STATOR #1 TRIP LEVEL
= XXX DEGREES C
= XXX DEGREES C
or
RTD #1 TRIP LEVEL
RTD #1 TRIP LEVEL
= XXX DEGREES C
= XXX DEGREES C
0-200 degrees C or OFF
(increments of 1)
(32-392 degrees F)
Factory Value = OFF
3.16
8
STATOR #2 ALARM LEVEL
STATOR #2 ALARM LEVEL
= XXX DEGREES C
= XXX DEGREES C
or
RTD #2 ALARM LEVEL
RTD #2 ALARM LEVEL
= XXX DEGREES C
= XXX DEGREES C
0-200 degrees C or OFF
(increments of 1)
(32-392 degrees F)
3.16
9
STATOR #2 TRIP LEVEL
STATOR #2 TRIP LEVEL
= XXX DEGREES C
= XXX DEGREES C
or
RTD #2 TRIP LEVEL
RTD #2 TRIP LEVEL
= XXX DEGREES C
= XXX DEGREES C
0-200 degrees C or OFF
(increments of 1)
(32-392 degrees F)
Factory Value = OFF
3.16
10
STATOR #3 ALARM LEVEL
STATOR #3 ALARM LEVEL
= XXX DEGREES C
= XXX DEGREES C
or
RTD #3 ALARM LEVEL
RTD #3 ALARM LEVEL
= XXX DEGREES C
= XXX DEGREES C
0-200 degrees C or OFF
(increments of 1)
(32-392 degrees F)
Factory Value = OFF
3.16
Содержание MULTILIN 269 MOTOR MANAGEMENT RELAY Series
