background image

Design Guide

5

36" Frame to 

Frame Width

*84" From

Floor to

Top Frame

35"

Case Width

*83-1/2" 

at

Rear

25-3/8" Framed Models

25-3/4" Stainless Steel Models

Case Depth

Depth Including Handles:

26-7/8" Framed Models

27-3/4" Stainless Steel Models

28-11/16" Professional Models

THE INSTALLATION SPACE

Water And Electrical Locations  

Electrical and water supply must be located as shown.
The Cutout Depth Must Be 24” Minimum for Standard 

Installation 

The unit will project forward, slightly beyond adjacent 

cabinetry, depending on your installation.
Cutout Depth Beneath a Soffit: 

When installed beneathh a soffit, the soffit cannot 

exceed the 24” installation depth shown. The top case 

trim overlaps the bottom of the soffit.

The Cutout Depth Must Be 26-3/16” For Flush 
Installation
Wooden cleats are required for flush installation. See 
Side Cleats on page 11.
Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply  

is required. An individual properly grounded branch  

circuit or circuit breaker is recommended. Install  

a properly grounded 3-prong electrical receptacle 

recessed into the back wall. Electrical must be  

located on rear wall as shown.

Note: GFI (ground fault interrupter) is not 

recommended.

• Water line can enter the opening through the  

floor or back wall. The water line should be 1/4” O.D. 

copper tubing or GE QuickConnect

 kit between the 

cold water line and water connection location, long 

enough to extend to the front of the unit. Installation 

of an easily accessible shut-off valve in the water line 

is required.

DIMENSIONS AND CLEARANCES

* Shipping height. The  

product can be adjusted 

to fit into a cutout that  

is 84-1/2” max. height. 

Note that the top case 

trim at the front is 1/2” 

higher and will overlap 

upper cabinetry or sof-

fit. Use leveling legs and 

wheels for a maximum 1” 

height adjustment.

Product Clearances

These units are equipped with a 3-position door stop.  

The factory set 115° door swing can be adjusted to 90°  

if clearance to adjacent cabinets or walls is restricted. 

Order WX14X99 door stop for precise settings between 

90° and 130°.

130° Door Swing

90° Door Swing

Allow 25” minimum clearance for a full 130° door 

swing. Allow 15” for pan removal.
For a 90° door swing, allow 4” minimum clearance to 

a wall for framed and stainless steel models. Allow 5” 

minimum clearance for professional models. If the 90° 

doorstop position is used, pan access is maintained but 

pan removal is restricted.
See illustrations pages

 

6 and 7

 

to determine door swing 

interaction with adjacent cabinets or countertops.

*

4

 stainless and trimmed 

models. 5

 Pro models.

*For standard installation, the finished cutout width 

must be 35-1/2”.

*For flush mount installation, the finished cutout width 

must be 39”.

115° Door Swing

Содержание Monogram ZIRS360NNLH

































Отзывы: