GE Mini Telemetry Скачать руководство пользователя страница 21

Страница: 21 / 71

2049809-001 Rev B

Chapter 2: Safety

WARNING

RECEIVER CONNECTORS: Operator shall not touch the J1 and J2 connector at the back plate of the

Receiver and the patient simultaneously
WARNING

INTERFERENCE: The use of TENS (Transcutaneous Electrical Nerve Stimulation) used for pain relief

in labor can interfere with fetal/maternal monitoring with Coro monitors.
WARNING

APPLIED PARTS: Audio headset and the transducer cables can also come in contact with the patient

other than the labeled applied parts. These are classified as Type B.

WARNING

BATTERY: Only GE authorized / recommended battery pack shall be used to avoid wrong mounting

of battery, dangers related to polarity reversal, short circuit or flames.

The following table contains cautions for this manual. A Caution statement is used when the possibility of

damage to the equipment exists.

CAUTION

Mini Telemetry services shall be done only by authorized service personnel.
CAUTION

ANNUAL SERVICING—For continued safety and performance of the equipment, it is recommended

that the calibration, accuracy and electrical safety of the equipment be verified on an annual basis

by an Information Technologies Service Representative.
CAUTION

DAILY INSPECTION—It is essential that the equipment and accessories be inspected prior to every

use.
CAUTION

ENVIRONMENT—The performance of the equipment has not been tested in certain areas, such as

x-ray and imaging suites. The equipment is not recommended for use in these environments.
CAUTION

PERFORMANCE—Report all problems experienced with the equipment. If the equipment is not

working properly, contact your Service Representative for service. The equipment should not be

used if it is not working properly.
CAUTION

Check the health of the line voltage. Few hospital sites may find noise in FECG/MECG when used

with power adaptor.
CAUTION

Periodic check needs to be done for mother’s parameter by the caregiver to ensure uninterrupted

monitoring.
CAUTION

Avoid over charging the battery or shorting the battery terminals.
CAUTION

STANDARD MAINTENANCE: Standard maintenance must be performed by authorized service

personnel for the lifetime of the product (7 years).
CAUTION

ULTRASOUND TRANSDUCER: Visually inspect the ultrasound transducer on a regular basis to ensure

there are no cracks or damages around the transducer face, cable, strain relief and connector pins.

Содержание Mini Telemetry



































































Результаты поиска

Содержание Mini Telemetry

Отзывы:

Похожие инструкции для Mini Telemetry

Бренды по названию

Популярные бренды

GE Mini Telemetry, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Mini Telemetry

Отзывы:

Похожие инструкции для Mini Telemetry

Бренды по названию

Популярные бренды