GE Mini Telemetry Скачать руководство пользователя страница 53

Страница: 53 / 71

2049809-001 Rev B

Chapter 6: Troubleshooting

Troubleshooting

Problem

Probable Cause

Solution

Radio channel number does

not appear in the normal

user screen on transmitter

display

• Currently configured radio

channel number is outside the

supported range as specified

in service manual.

•

Communication between the

system and the radio module

is not established.

•

Radio module is defective.

Contact your Information Technologies

Service Representative.

Bad Radio Icon

appears on the

transmitter screen

•

Transmitter frequency is

outside the range of the radio

module.

•

Communication between the

system and the radio module

is not established.

•

Radio module is defective.

Contact your Information Technologies

Service Representative.

Bad battery icon

appears on the

transmitter screen

•

Transmitter battery pack over

discharged

•

Connect the power adaptor to the

transmitter and charge for 15 minutes.

Disconnect the power adaptor and

reconnect. Switch on the transmitter

and check if bad battery symbol is

replaced with the battery status.

•

Disconnect the battery from the

battery compartment. Refer to section

6.1.1 of Mini-telemetry service manual

for battery replacement procedure.

Reconnect the battery and repeat the

previous step.

•

Disconnect the battery from the

battery compartment. Refer to section

6.1.1 of Mini-telemetry service manual

for battery replacement procedure.

Using an external DC source (8.5V and

current limited to 1000mA), charge the

battery for 5 minutes. Reconnect the

battery and repeat the previous step.

•

Defective battery

•

Battery not able to charge

•

Contact your Information Technologies

Service Representative.

•

Replace the battery

Содержание Mini Telemetry



































































Результаты поиска

Содержание Mini Telemetry

Отзывы:

Похожие инструкции для Mini Telemetry

Бренды по названию

Популярные бренды

GE Mini Telemetry, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Mini Telemetry

Отзывы:

Похожие инструкции для Mini Telemetry

Бренды по названию

Популярные бренды