background image

10

D0404SG0_B

KTD-404 Controller Keypad Installation and Operations Guide

Camera Site Access

System Size

Step 3)

The  CLEAR  MEMORY  option  will  erase  all  data  in  the  controller  keypad’s

nonvolatile memory and reload factory default values.

To clear the keypad’s memory, press  

1

.  The display will automatically advance

to the menu shown in Figure 11.

If the CLEAR MEMORY function is not to be used, press  

0

 and go to Step 5.

Step 4)

This menu offers a safety check. If a  

3

 is entered, the controller keypad’s

memory will be reloaded with factory default values. If a 

0

 is entered, there will

be no change. The display will automatically advance to the next menu.

Step 5)

This menu is used to set the system size. Use the numerical keys to enter the

largest camera number, largest monitor number, largest multiplexer number, and

largest  preset  number  in  the  system.  Maximum  entries  are:  cameras-511,

monitors-64, multiplexers-64, and presets-63.

Press  

seq

  to advance to the next column, or move the joystick left or right to switch

between  columns.    Once  all  entries  are  made,  the  display  will  automatically

advance to the next menu.

Step 6)

This menu is used to deny or permit the controller keypad’s access to certain

camera sites. Press 

0

 to deny access or 

1

 to permit access. After each

selection, the next camera number will appear.  Move the joystick up or down to

switch between cameras.  When done, press 

seq

 to advance to the next menu.

Figure 13: Camera Site Access Display

CAMERA 000  ACC=YES

0=NO 1=YES      SEQ=NEXT

Figure 12: System Size Display

SYST SIZE     (CAMERAS)

511 64 64 63    SEQ=NEXT

Figure 11: Second Clear Memory Display

ARE YOU SURE?

0=NO 3=YES      SEQ=NEXT

Clear Keypad Memory

Figure 10: Clear Memory Display

CLEAR MEMORY?

0=NO  1=YES     SEQ=NEXT

Helpful Hint:

 Pressing the 

seq

 key will forward you through programming without changing

the set parameters.

Содержание KTD-404













Отзывы: