GE IC754CSF15CTD Скачать руководство пользователя | Manualshive

Страница: 12 / 102

background image

1-4

15" QuickPanel* View &

QuickPanel Control

Loaded Color TFT

– December 2011 GFK-2402D

1

7. In the Control Panel, double-tap

Network and Dial-up Connections to

configure network settings.

8. To save the settings, run

Backup.

Shutdown

There are no specific dangers associated with a power failure or other
unplanned shutdown of the QuickPanel View/Control. In general, programs
are retained in FLASH memory and user data can be retained in battery-
backed SRAM. Some operating system settings are retained only with user
intervention, so in order to carry out a graceful shutdown of the QuickPanel
View/Control, we recommend you perform the following procedure.

To shut down the QuickPanel View/Control

1. Quit any programs that are running and wait for all file operations to

complete.

2. If you have not changed operating system settings (e.g., brightness or

touch screen sensitivity) or do not want to save the changes, remove
AC power from the DC supply.

3. To save changes to operating system settings (e.g., brightness, touch

screen sensitivity), run

Backup and then reboot the system. When

the Windows CE desktop reappears, remove AC power from the DC
supply.

Firmware Updates

Updates to the QuickPanel firmware will be made available through the
Technical Support web site. (See page

iii

for contact information.) This will

allow updating the unit to the most recent released version of the firmware
with the latest feature updates and defects addressed.

«
...
10
11
12
13
14
...
»

Содержание IC754CSF15CTD







































































































Отзывы:

Нет отзывов

Похожие инструкции для IC754CSF15CTD

Бренд: rada Страницы: 16

Бренд: Rane Страницы: 2

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренд: S&C Страницы: 11

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 19

Бренд: Water Specialist Страницы: 60

Бренд: Paradox Страницы: 3

Бренд: M-system Страницы: 7

Бренд: SMC Networks Страницы: 10

Бренд: QUICK DAM Страницы: 16

SR-ZG9001T-RGBW

Бренд: Sunricher Страницы: 3

Бренд: Mosa Страницы: 28

Бренд: Gateway Страницы: 2

Бренд: CALEFFI Страницы: 6

Бренд: Oriental motor Страницы: 4

Бренд: National Instruments Страницы: 26

Бренд: Lab-T Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды