CHAPTER 5: CONFIGURING THE SOFTWARE
D20MX HARDWARE USER’S MANUAL
GE INFORMATION
73
11.2. Click the D20 device.
11.3. Click the ribbon
Configure
group >
Edit
>
Copy
.
11.4. Click a blank area on the page onto which the copy is to be placed.
11.5. Click the ribbon
Configure
group >
Edit
>
Paste
.
Result: The Copying device window appears.
Result: Once completed a new device named COPY_OF_<original device
name> or <original device name>_COPY appears.
12. Select a D20MX processor from the D20 Device Wizard:
12.1. Click the
Project
tab of
the original D20 device configuration
.
12.2. Click the D20 device.
12.3. Click the ribbon
Configure
group >
Edit
>
Properties
.Result: A Warning prompts
you to save an internal backup copy.
12.4. Click
Yes
to create a backup, or
No
to not create a backup.
Result: The D20 Device Wizard Basic Settings window appears.
12.5. Click
Next
until the Processor tab appears.
12.6. Click the
Processor
tab >
General
sub-tab.
12.7. From the Part Number field, click
Select
.
Result: The Select a Processor Card window appears.
12.8. Select one of the three D20MX processor type part numbers (526-3001, 526-
3003 or 526-3005).
12.9. Click
OK
,
Firmware
tab, and
Select
.
12.10. Select either
SAN0001 / 002
or
SAN0002 / 002
as per the decision taken in step
2
.
If you had opted to upgrade the firmware in ConfigPro, then this step is not
necessary.
12.11. Click
OK
.
12.12. Click
Next
and
Finish
.
Result: The D20 Device Wizard closes.
Note
: This process can take awhile. Most of the warnings that occur at the end
of this process will disappear after the completion of Step 18.
13. Ensure the BOOTP client is disabled:
13.1. Click the
Project
tab of
the original D20 device configuration.
13.2. Click the D20 device.
13.3. Click the ribbon
Edit
group >
Properties
.
Result: A Warning prompts you to save an internal backup copy.
13.4. Click
Yes
to create a backup, or
No
to not create a backup.
Result: The D20 Device Wizard appears.
13.5. Click
Next
until the Processor tab appears.
13.6. Click the
LAN Settings
tab >
General
sub-tab.
13.7. From the BOOTP Settings frame, ensure
Not Used
is checked.
13.8. Click
Next
and
Finish
.
Result: The D20 Device Wizard closes.
14. Disable unused applications:
14.1. Click the
Project
tab of
the original D20 device configuration.
14.2. Double-click the D20 device.
Result: The Application List popup appears.
Содержание D20MX
