GE Adora DFE29JG Скачать руководство пользователя страница 67

Страница: 67 / 91

– 67 –

Ice Box Door Assembly

The ice box door assembly consists of the door,
latch, and gasket.

The ice box door assembly is attached to the left-

side refrigerator door with 2 hinges. To remove the
ice box door assembly, it is necessary to open the
door and remove the two T-15 Torx screws and the
top hinge. The door assembly can then be lifted off
the bottom hinge.

Door Latch

Door Gasket

Door Panel

Top Hinge

The door latch cover must be removed to access the

latch to the ice box door. The cover is attached to
the door with 2 rear tabs and 2 front tabs. A small

at blade screwdriver can be used to pry out the

front of the latch cover.

The cover can then be pulled toward the latch

handle and removed.

Door Latch Cover

(

Continued next page

)

Содержание Adora DFE29JG




























































































Результаты поиска

Содержание Adora DFE29JG

Отзывы:

Похожие инструкции для Adora DFE29JG

Бренды по названию

Популярные бренды

GE Adora DFE29JG, Техническое обслуживание руководство

Результаты поиска

Содержание Adora DFE29JG

Отзывы:

Похожие инструкции для Adora DFE29JG

Бренды по названию

Популярные бренды