GE Adora DFE29JG Скачать руководство пользователя страница 50

Страница: 50 / 91

– 50 –

7. Prepare the replacement thermistor by cutting

the wiring 4 inches back from the thermistor
and strip the wires back 3/16 inch.

8. Using two WR01X10466 bell connectors, splice

the wiring. After the splices are complete,

ll the

bell connectors fully with WR97X163 silicone
grease.

Silicone Grease

9. Snap the thermistor into the grille and replace

the foil shield (if present) inside the cover. Place
excess wiring into the thermistor pocket, then
snap the grille back into the liner, taking note of
the alignment pin.

4. Pull the thermistor out from the 4 tabs in the

cover.

Thermistor

Tab (1 of 4)

5. Cut the thermistor wiring as close to the

thermistor as possible.

6. Strip the outer insulation from the thermistor

case harness back 1 inch. Strip the 2 internal
wires back 3/16 inch for splicing.

3. Peel back the foil shunt (if present) from the

cover.

Thermistor Cover

Foil Shunt

To replace a fresh food or freezer air thermistor:

1. Unplug the refrigerator.

Note:

The thermistor grille uses an alignment tab to

ensure proper grille placement. The grille also uses 2
snap tabs to lock it into the liner.

2. Insert a small

at blade screwdriver under the

thermistor cover and gently lift the edge until it
releases from the ceiling.

Snap Tabs

Alignment

Tab

Содержание Adora DFE29JG




























































































Результаты поиска

Содержание Adora DFE29JG

Отзывы:

Похожие инструкции для Adora DFE29JG

Бренды по названию

Популярные бренды

GE Adora DFE29JG, Техническое обслуживание руководство

Результаты поиска

Содержание Adora DFE29JG

Отзывы:

Похожие инструкции для Adora DFE29JG

Бренды по названию

Популярные бренды