manualshive.com logo in svg

GE Adora DFE29JG, Техническое обслуживание руководство, Страница: 66 / 91

Поделиться
Скачать
GE Adora DFE29JG Скачать руководство пользователя страница 66

– 66 –

Lower Ultrasonic Sensor Assembly

The lower ultrasonic sensor assembly is attached 

to the back of the dispenser cavity with 2 tabs (1 on 
each side) located behind the front trim. 

To remove the lower ultrasonic sensor assembly:

Note:

 Tabs on the sensor assembly are fragile. Do not 

remove unless a replacement sensor is on hand.

1.  Remove the actuator paddle and switch. (See 

To 

remove the actuator paddle and switch

.)

2.  Remove the lower ultrasonic sensor assembly 

wires from the retainer in the cavity channel.

Caution: 

To prevent damage to the lower ultrasonic 

sensor assembly and the dispenser recess, in the 
following step, use a non-marring tool (plastic 
putty knife) to gently pry the sensor tabs out from 
the dispenser cavity. Take care not to scratch the 
dispenser recess.

3.  Pry out the sensor assembly, then grasp and 

pull the sensor assembly out from the dispenser 
cavity.

Retainer

Lower Ultrasonic 

Sensor Assembly

Tab (1 of 2)

Sensor Assembly (rear view)

4.  Pull sensor wiring thru opening in the bottom of 

the dispenser channel.

Opening

4.  Tilt the top of the paddle out, then remove it 

from the dispenser recess.

Note:

 The paddle and switch are supplied as an 

assembly. The spring is inserted around a post and 
is available separately.

Post

Spring

Switch

Содержание Adora DFE29JG




























































































Отзывы:

Нет отзывов