GE Adora DFE29JG Скачать руководство пользователя страница 57

Страница: 57 / 91

– 57 –

Freezer Evaporator Thermistor

The freezer evaporator thermistor is attached to the

suction line with a metal clip. The purpose of the
thermistor is to monitor the evaporator temperature
for defrost control.

To access the freezer evaporator thermistor the

freezer evaporator cover must be removed. (See

Freezer Evaporator Cover

Note:

The ice box fan wire connector also contains

the freezer evaporator thermistor connections. The
freezer evaporator thermistor can be replaced
separately (Part #WR55X10025).

When replacing the freezer thermistor:

1. Place the replacement thermistor next to the

original thermistor.

2. Cut the wiring at a location that will match the

original length when the replacement thermistor
is spliced to it.

3. Use plastic bell connectors (Part # WR01X10466).

Fill each connector with silicone grease then
splice a new thermistor into the harness as
shown in the illustration.

Freezer Thermistor

Clip

Silicone Grease

Ice Box Fan

The ice box fan is located at the top left rear of the

freezer compartment above the evaporator. The ice
box fan circulates air into the left fresh food door ice
box via duct work foamed into the case.

Return Air

Supply Air

The fan will operate at 3 speeds with RPM feedback

to the control. Speeds selected depend on the ice
box cooling temperature and are controlled by the
main board. Approximate fan speeds are:

Low Speed = 1500 RPM
Medium Speed = 1800 RPM
High Speed = 1800 RPM

Supply Air

Return Air

(

Continued next page

)

Содержание Adora DFE29JG




























































































Результаты поиска

Содержание Adora DFE29JG

Отзывы:

GE Adora DFE29JG, Техническое обслуживание руководство, Страница: 57 / 91

Результаты поиска

Содержание Adora DFE29JG

Отзывы: