GDZX ZXMD-2001 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 25

GDZX ZXMD-2001 Скачать руководство пользователя страница 22

21

4.

The calibrated density relay cannot be laid flat and placed vertically,

otherwise the calibration will be inaccurate.

5. The density relay shall not vibrate too much in the process of verification.
6. When using the gas cylinder, follow the instructions below.

9

、

Custody and transportation

1. The calibration device belongs to the precision electronic product, which

should be placed in the temperature of - 30 ~ 70

℃

, the relative humidity is

not more than 90%, and the air does not contain enough gas to cause
corrosion.

2. During the transportation of calibrator, avoid violent vibration and impact,

and prevent rain and snow from soaking.

10

、

After sales service

All users who purchase our products enjoy the following after-sales

services:

Within one month from the date of sale of the instrument, if there is any

quality problem, our company will replace the new meter free of charge, but
the user cannot dismantle the machine by himself.It is not included in this
scope due to improper use of users (such as wrong plug-in power supply,
water inflow and appearance mechanical damage).

All quality problems of instruments within one year shall be repaired by our

company free of charge.

«
...
20
21
22
23
24
...
»

Содержание ZXMD-2001


























Отзывы:

Нет отзывов