GBC FusionPunch II Service Manual
RAP 4.1 Document Transport Jams
12/2003
2-28
2A. The Document Transport Motor is
enabled by a ground on P11-MT2. When
the output is activated, there should be
0VDC at this point. When it is deactivated,
there should be +24 VDC at this point.
Activate and then deactivate the output
and check for 0 VDC and then +24 VDC
between P/J11-MT2 and P/J 12-0V on the
Punch AC/DC Distribution PWB.
There is 0 VDC when the output is
activated and +24VDC when the output is
deactivated.
Y
N
Replace the Punch I/O PWB (PL 3.1).
Activate the output and check AC voltage
across J8-NUI and J8-MT2 on the Punch
AC/DC Distribution PWB.
There is 110 VAC at this point.
Y
N
Replace the Punch AC/DC
Distribution PWB (PL 3.1).
Check the harness from J8-NUI on the
Punch AC/DC Distribution PWB to the
Document Transport Motor, and from J8-
MT2 on the Punch AC/DC Distribution
PWB to the Document Transport Motor. If
the harness is OK, replace the Document
Transport Motor (PL 1.1B).
3.
Disconnect P/J30 on the Punch I/O PWB.
Activate the output again and check LED
L0A8 on the Punch I/O PWB.
The LED is lit when the output is active.
Y
N
Check continuity between J1-HV08
on the Little Star Controller PWB and
P22-OUTB1 on the Punch I/O PWB.
Go to Step 3A.
Go to Step 3B.
3A. If faulty, replace the harness (PL
6.1D). If the harness is OK, replace
the Little Star Controller PWB (PL
3.1).
3B. Check continuity and for shorts to
ground between P 30-OUTA,C8 on the
Punch I/O PWB and P11-MT2 on the
Punch AC/DC Distribution PWB.
The harness is OK.
Y
N
Replace the harness (PL 6.1A)
The Document Transport Motor is enabled
by a ground on P11-MT2. When the output
is activated, there should be 0VDC at this
point. When it is deactivated, there should
be +24 VDC at this point.
Activate and then deactivate the output
and check for 0 VDC and then +24 VDC
between P/J11-MT2 and P/J 12-0V on the
Punch AC/DC Distribution PWB.
There is 0 VDC when the output is
activated and +24VDC when the output is
deactivated.
Y
N
Replace the Punch I/O PWB (PL 3.1).
Activate the output and check AC voltage
across J8-NUI and J8-MT2 on the Punch
AC/DC Distribution PWB.
There is 110 VAC at this point.
Y
N
Replace the Punch AC/DC
Distribution PWB (PL 3.1).
Check the harness from J8-NUI on the
Punch AC/DC Distribution PWB to the
Document Transport Motor, and from J8-
MT2 on the Punch AC/DC Distribution
PWB to the Document Transport Motor. If
the harness is OK, replace the Document
Transport Motor (PL 1.1B).
4.
The paper jams in the Punch Document
Transport Assembly.
Y
N
Go to Step 5.
Using the information in the table below,
enter the Diagnostics mode and use the
left/right keys to select the Deck Motor
output. Activate the Document Transport
Motor.
When the motor activates, the infeed belts
in the Document Transport Assembly drive
smoothly.
Y
N
Grasp the Document Transport Main
Drive Timing Belt and pull it in a
counterclockwise direction to test its
motion, and the motion of the infeed
belts in the subsystem in which the
jam is occurring.
If the belts in any area binding, loose,
or are not rotating smoothly, check the
belts, pulleys, idlers and shafts to
ensure proper operation. Repair/
replace as required (PL 4.2A - 4.2E).
Check the Document Transport Assembly
for obstructions, burrs, bent or missing
components. Repair/replace as required
(PL 4.2A - 4.2E).
Output
Diagnostic
Document
Transport
Motor
P OUTA8 Deck Motor
O8 1100110011001100
Содержание FusionPunch II
