manualshive.com logo in svg

Gateway 850, Руководство пользователя, Страница: 40 / 88

Поделиться
Скачать
Gateway 850 Скачать руководство пользователя страница 40

36

Chapter 3: Monitoring Systems

www.gateway.com

The following are examples of the one-touch annunciation LEDs for switch 
settings and controller and bus configurations when the Alarm Reset button is 
pressed.

JBOD single-bus configuration annunciation LED sample

SAF-TE switches 1 (A0) and 2 (A1) work in combinations to create a specific 
range of SCSI IDs. The LED state provides the following information:

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Drive Slot 1

Drive Slot 4

Drive Slot 7

Drive Slot 10

Drive Slot 2

Drive Slot 5

Drive Slot 8

Drive Slot 11

Drive Slot 3

Drive Slot 6

Drive Slot 9

Drive Slot 12

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Drive Slot 1

Drive Slot 4

Explanation of LEDs

Example of LEDs

Drive Slot 7

Drive Slot 10

Drive Slot 2

Drive Slot 5

Drive Slot 8

Drive Slot 11

Drive Slot 3

LED ON Condition (Green)

LED OFF Condition

Drive Slot 6

Drive Slot 9

Drive Slot 12

R
D

A
0

1 2 3 4 5 6 7 8

A
1

S
0

S
1

B
D

D

L

R
M

UP (1)

DOWN (0)

SAF-TE Disk I/O Card

Switch Settings

Содержание 850

























































































Отзывы:

Нет отзывов