Gateway 850 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 88

Gateway 850 Скачать руководство пользователя страница 37

33

Enclosure component monitoring

www.gateway.com

Drive LEDs

The Drive LEDs are comprised of Drive Status and Drive Activity LEDs and are
located on the left side of the front bezel between the ventilation ribs. The Drive
LEDs are grouped in pairs and are in the general location of the drive slot.

These Drive LEDs assist with identifying which drive is experiencing I/O
activity, array status, and the presence of a drive in a drive slot.

The Drive Status LEDs comprise the “One-Touch Annunciation” monitoring
system which can display the status of controllers and SAF-TE card switch
settings from the touch of the Alarm Reset button. For more information, see
“One-touch annunciation” on page 35.

RESET ALARM

Drive LEDs

Alarm Reset Button

(Press to Display Annunciation)

Power LED

Channel

Status LED

Power Supply
Status LED

Cooling Fan
Status LED

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Drive Slot 1

Drive Slot 4

Drive Slot 7

Drive Slot 10

Drive Slot 2

Drive Slot 5

Drive Slot 8

Drive Slot 11

Drive Slot 3

Drive Slot 6

Drive Slot 9

Drive Slot 12

«
...
35
36
37
38
39
...
»

Содержание 850

























































































Отзывы:

Нет отзывов