Gates Unitta Asia U-507 Скачать руководство пользователя страница 7

Страница: 7 / 16

1. Press "MEASURE" button to set up auto trigger mode.

＊

Initial display status is

Measurement thereafter is started by receiving signals from the sensor.

＊

Displays

during measurement.

＊

After turning on power, allow an interval of 1 second or longer before pressing "MEASURE" button

for automatic gain adjustment.
2. When the belt type is changed, press "MEASURE" button to start measurement.
3. When measurement frequency range is changed, press "MEASURE" button to start measurement in changed
frequency range.

"MEASURE"
button

The following two types are available.
The microphone itself has a small diameter of 12.5 mm attaching flexible pipe system, and can be positioned with
single hand from the main body, and it is useful in a place where the main body cannot be placed on floor such as a
manufacturing site. Compatible with entire measurable frequency band: 10 - 5000Hz.
Note: Do not hold and twist the microphone and connector area.

Measurement
sensor microphone/
flexible arm system
microphone
(standard
specification)

LCD screen
with backlight

●

Belt type and unit mass are displayed when this button is held down one second or

longer.Choose a desired belt type by use of "UP" and "DOWN" button, and determine
by "MEASURE" button. (See page 9 for preinstalled unit mass.)

＊

Display unit : g/m.

＊

CAT (rough standard), tension, and frequency are displayed only when belt type is chosen by MASS button.

Select button

●

Press SELECT button to choose any desired input number displayed in power-on.

20 memory functions selectable from No. 0 to 19

＊

Call out numbers sequentially forward by pressing SELECT button, and press any number to jump to designated

number. Here, when you call out No. 10 or larger, press the number continuously.

WIDTH button

●

Choosing "WIDTH" button enables input of belt width with use of numeric key.

Allowed input capacity: 000.1 - 999.9 mm/R

＊

Enter the number of ribs for V belt.

SPAN button

●

Choosing "SPAN" button enables input of measurement span length with use of numeric key.

Hz button
(switching
between
frequency and
tension modes)

●

Pressing "Hz" button enables choosing between

measurement tension display and measurement frequency
display.

＊

Display changes every time this button is pressed.

●

In addition, holding down Hz button enables dual display

with tension and frequency. However, CAT display is
available only when inputting from preinstalled data.
(Displays only for timing belt.)

＊

Displayed CAT value for tension and frequency are

slightly different from standard installation tension of toothed
belt on page11. Use them as a rough standard.

0-button
(frequency range
switching)

Hold down "0" button one second or longer to change measurement frequency range.
HIGH

………………500〜5000Hz

STANDARD

………10〜600Hz

LOW

………………10〜50Hz

Choose a range with UP and DOWN button, and determine with "MEASURE" button.
In selecting 600Hz or above, the range must be switched to "HIGH range".
Determine with "MEASURE" button.

The microphone itself has a small diameter of 12.5mm attaching cord system. It enables measurement in any use
such as in congested places hard to measure. Conpatible with entire measurable frequency band: 10 - 5000Hz.

Cord system
microphone
(option)

S No. 1

M 9 9 9 .9 g/m
W 9 9 9 .9 mm/R
S 9 9 9 9 mm

Display of measured tension

Double display of measurement tension
and frequency

Dual display of measured
frequency and catalog frequency

Double display of measurement
tension and catalog tension

Display of measurement frequency

S No. 2 2GT

TENSION

99900 N

Measurement
frequency level

H : HIGH
S : STANDARD

L : LOW

Memory No.

Measured tension

＊

In measurement of belt type

Remaining battery

[Overview of LCD indication pattern]

＊

Displayed only when

input from preinstallation

Example of display indication unit mass, belt width,so span.

●

Displays tension value, etc.

●

Displays tension by three significant digits from 0.01 to 99900.

●

Displays frequency by three significant digits from 10.0 to 5000 Hz.

●

When the tension measurement result is out of the standard

speciffcation, LED (red) turns on and "ERROR" is displayed.
* When tension exceeds its range after measurement result is
displayed, the value for the last 2times are displayed, and retrial is
prompted by "peep" sound.

●

Battery mark is displayed when battery is consumed.

(When remaining voltage is low, the battery mark blinks, as well as
"LOW BATT" blinks.)

●

Backlight is always on.

However, it will turns off if it mot in use is not used for one minute, and
will resume when operated again.

S No 02 2GT

1.5GT 0.9

1
2
3

3GT 2.5

2GT 1.3

MASS button
(unit mass)
UP DOWN button