EN
EN
108
109
2. Hold the mincer housing with the thread facing upwards and insert the worm shaft
with the long, hexagonal shaft facing downwards. When inserted correctly, the
hexagonal shaft protrudes the mincer housing at the coupling side (bottom).
3. Place the black plastic cross (cookie adapter) on the pin in the centre of the
worm shaft. Ensure correct orientation: the label .“FRONT” must face upwards.
Turn the cookie adapter until the spigots at the rim of the cookie adapter engage
in the notches at the rim of the mincer housing.
4. Place the metal cover on the cookie adapter and turn the metal cover until the
notches at the rim slide onto the spigots of the cookie adapter. If positioned cor-
rectly, there is no gap between the cookie adapter and the metal cover.
5. Turn the screw ring hand-tight onto the mincer housing.
6. Prepare the machine for operation (see: ‘Preparation’).
7. For removing the protecting cover of the mincer coupling at the mixing arm, turn
the protecting cover clockwise and pull it out.
8. Holding the feed chute of the mincer in the 2'clock position, insert the coupling
of the mincer with the protruding hexagonal shaft into the mincer coupling of the
mixing arm. If required, turn the mincer to and fro a little until it slides into the
mincer coupling.
9. While pressing the release button, turn the mincer counter-clockwise to the stop.
The feed chute must face upwards vertically and the mincer must be engaged
firmly, when releasing the release button.
10. Place the tablet onto the feed chute of the mincer.
11. From the side of the mincer, insert the cookie mask into the slit between the metal
cover and cookie adapter and push the cookie mask in, until the desired ope-
ning is positioned in the centre of the metal cover.
NOTE
You select the shape of your cookies via the position of the cookie mask.
Forming the Cookie Dough
12. Place the dough roll onto the tablet of the mincer.
13. Connect the machine to a suitable wall power outlet (see: ‘Important Safegu-
ards for Electrical Appliances’). The display areas show dashes and an acoustic
signal sounds. The stand mixer is in standby mode now.
WARNING
– Do not hold your hands or any foreign objects (e.g. cooking
utensils) into the feed chute of the mincer or at the mixing drive, while the machine
is connected to the power supply. Always use the provided pusher for pushing
down your food within the feed chute.
14. Hold the control dial pressed for approx. 2 seconds for switching on the machi-
ne. A signal sounds and “00” flashes on the speed display. The operating time
display shows the default operating time: “20:00” (20 minutes).
15. If you wish a reminder for making breaks in time, you should set the timer of the
machine to 10 minutes (see: ‘Operating Time and Pause Function’).
16. Turn the control dial until the speed setting “10” is shown at the speed display.
17. It is best to hold your hand or a small tablet directly below the outlet of the min-
cer, while pushing the dough roll into the feed chute. Try to push the dough as
evenly as possible into the feed chute. Let the shaped dough slide onto your
hand or onto the tablet.
18. When the piece of dough coming out of the mincer has reached the desired
length, cut off the dough via a sharp knife or pair of scissors just at the outlet of
the mincer. If required, stop the motor for this by pressing the control dial (see:
‘Operating Time and Pause Function’). However, when being experienced, you
may keep the motor running, while separating the shaped pieces of dough.
19. Put down the pieces of shaped dough onto the tablet or baking tray, while a
second person is inserting the dough roll slowly into the opening of the feed
chute. If required, use the pusher to push your food slowly and without much
pressure down in the feed chute.
20. After processing the prepared dough roll, press the control dial for stopping the
motor (see: ‘Operating Time and Pause Function’).
21. If required, prepare the next dough roll and place it onto the tablet of the mincer.
Then repeat steps 16 to 20.
22. When you do not wish to use the machine for another portion, switch off the
machine by holding the control dial pressed until only dashes are displayed
(see: ‘After Usage’). Unplug the machine.
23. Remove the mincer from the mixing arm (see: ‘After Usage’). Immediately there-
after, clean the machine and any used accessories (see: ‘Care and Cleaning’).
NOTE
You should bake the prepared cookies immediately according to the instructions
in your recipe.
