Gaspardo FIORE, Использование и обслуживание / Запасные части

Страница: 53 / 178

USE AND MAINTENANCE
ENGLISH
53
-
cod. G19503900
7KHFKHFNPXVWEHFDUULHGRXWRQDOOEODGHJXLGHV)LJXVLQJ
DPPWKLFNVKLPSODWHVXSSOLHG
Always use personal protective equipment.
The tolerance allowed for optimal coupling is determined by
the insertion of a single plate
2)LJ
,IDSODWHGRHVQRW¿WEHWZHHQWKHWHHWKEODGHDQGWKHEODGHJXLGH
RQHPXVWDGGDVKLP)LJ
,ILQVWHDGWZRFRXSOHGSODWHVFDQEHLQVHUWHG3)LJRQHPXVW
UHPRYHDVKLPWRUHVWRUHWKHRSWLPDOFRXSOLQJWROHUDQFHFRQGLWLRQV
&$87,21ZKHQ¿WWLQJWKHEODGHJXLGHLWLVLPSRUWDQWWROHDYH
a coupling tolerance of about 1 mm with the sections holder
rod (L, Fig. 39).
2QO\ZLWKVRPHPRGHOVEHIRUHGLVDVVHPEOLQJWKHEODGHJXLGHV1
)LJRQHPXVWSUHYLRXVO\UHPRYHWKH¿QJHUEODGHWLHURG4
in Figure 43. Use a punch to facilitate the operation (R, Fig. 43) .
6XEVHTXHQWO\RQO\DIWHUKDYLQJPDGHVXUHWKDWWKHEODGHJXLGHV
KDYHEHHQEORFNHGRQHPXVWWLJKWHQWKH¿QJHUEODGHDJDLQYLDWKH
QXWVORFDWHGDWERWKHQGVNHHSLQJWRWKHPPVKRZQLQ)LJXUH
43. Use a punch to facilitate the operation (R, Fig. 43).
7KLVPHDVXUHPHQWDOORZVWRPDLQWDLQWKHFXWWLQJEDULQWUDFWLRQ
ZLWKRXWEHQGLQJLWGRZQZDUGV
IMPORTANT: when replacing the teeth or the tooth-holding
bar, carry out the check described above. When required, put
back the shims to avoid striation or damage.
STORAGE
,WLVDGYLVDEOHWRSURFHHGLQWKHIROORZLQJZD\DWWKHHQGRIWKHVHD
VRQRULIWKHPDFKLQHLVWRUHPDLQLQDFWLYHIRUDORQJSHULRGRIWLPH
7UHDWWKHLPSOHPHQWLQFRPSOLDQFHZLWKWKHLQVWUXFWLRQVJLYHQLQ
WKHFKDSWHUHQWLWOHG³ Cleaning and oiling the cutters ´
Carefully check for any damaged or worn parts and replace
these as necessary.
Fully torque all screws and bolts.
Apply protecting oil to all unpainted parts.
Protect the equipment with a (nylon) cover.
Lastly, store the implement in a dry place where it cannot be
tampered with by unauthorized persons; the mowing machi-
QHPXVWEHVHWXSRQÀDWDQGFRPSDFWJURXQGVXSSRUWHG
by the relative bearing struts (H-I, Fig. 38).
Careful compliance with these instructions will be all to the
advantage of the user who will be sure to use an implement
in perfect conditions when work begins again.
Fig. 40
302 mm
30 mm
1 mm
Fig. 41
Fig. 42
P O
Fig. 43
~15 mm
~15 mm
Q
R