GAS GAS MC 450F 2022 Скачать руководство пользователя страница 83

Страница: 83 / 157

SERVICE WORK ON THE CHASSIS 11

11.40

Checking the frame

S02306-01

–

Check the frame for damage, cracks, and deformation.
» If the frame shows signs of damage, cracks, or deformation:

–

Change the frame.
Guideline

Repairs on the frame are not permitted.

11.41

Checking the link fork

S02305-01

–

Check the link fork for damage, cracks, and deformation.
» If the link fork shows signs of damage, cracks, or deformation:

–

Change the link fork.

Info

Always replace a damaged link fork. GASGAS Motor-
cycles does not permit repairing link forks.

11.42

Checking the throttle cable routing

Preparatory work

–

Remove the seat. (

p. 65)

–

Remove the fuel tank.

(

p. 72)

A00892-10

Main work

–

Check the throttle cable routing.

Both throttle cables must be routed, side by side, on the back of
the handlebars and above the fuel tank bracket, to the throttle
valve body. Both throttle cables must be secured behind the rub-
ber strap of the fuel tank support.

» If the throttle cable is not routed as specified:

–

Correct the throttle cable routing.

Finishing work

–

Install the fuel tank.

(

p. 74)

–

Mount the seat. (

p. 65)

Содержание MC 450F 2022






























































































































































Результаты поиска

Содержание MC 450F 2022

Отзывы:

Похожие инструкции для MC 450F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 450F 2022, Руководство пользователя

Результаты поиска

Содержание MC 450F 2022

Отзывы:

Похожие инструкции для MC 450F 2022

Бренды по названию

Популярные бренды