GAS GAS MC 450F 2022 Скачать руководство пользователя страница 103

Страница: 103 / 157

WHEELS, TIRES 13

101

–

Hold the rear wheel and remove the wheel spindle. Take the rear
wheel out of the link fork.

Info

Do not operate the foot brake lever when the rear wheel is
removed.

H03002-10

–

Remove spacers

13.4

Installing the rear wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

H03001-10

Main work

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the rear wheel bearing.

–

Clean and grease shaft seal rings

and contact surfaces

of the

spacers.

Long-life grease (

p. 146)

–

Insert the spacers.

A00842-10

–

Clean and grease the wheel spindle.

Long-life grease (

p. 146)

–

Position rear wheel and insert wheel spindle

The brake linings are correctly positioned.

–

Mount the chain.

Содержание MC 450F 2022






























































































































































Результаты поиска

Содержание MC 450F 2022

Отзывы:

Похожие инструкции для MC 450F 2022

Бренды по названию

Популярные бренды

GAS GAS MC 450F 2022, Руководство пользователя

Результаты поиска

Содержание MC 450F 2022

Отзывы:

Похожие инструкции для MC 450F 2022

Бренды по названию

Популярные бренды