GAS GAS MC 450F 2022 Скачать руководство пользователя страница 28

Страница: 28 / 157

7 PREPARING FOR USE

7.7

Preparing the vehicle for rides on wet and muddy circuits

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Observe the fitting instructions for

GASGAS Techni-

cal Accessories

600868-01

–

Mount the steel sprocket.

–

Clean the motorcycle. (

p. 126)

–

Straighten the bent radiator fins carefully.

7.8

Preparing vehicle for high temperatures or slow riding

600868-01

–

Adjust the secondary drive to the road conditions.

Info

The engine oil heats up quickly when the clutch is operated
frequently due to an excessively high secondary ratio.

–

Clean the chain.

Chain cleaner (

p. 146)

–

Clean the radiator fins.

–

Straighten bent radiator fins carefully.

–

Check the coolant level. (

p. 110)

7.9

Preparing the vehicle for low temperatures or snow

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Observe the fitting instructions for

GASGAS Techni-

cal Accessories

Содержание MC 450F 2022






























































































































































Результаты поиска

Содержание MC 450F 2022

Отзывы:

Бренды по названию

Популярные бренды

GAS GAS MC 450F 2022, Руководство пользователя

Результаты поиска

Содержание MC 450F 2022

Отзывы:

Бренды по названию

Популярные бренды