background image

 4 

WARRANTY 

 
This warranty covers defects in material and 
workmanship under normal use providing that: 
 
a) the equipment has not been accidentally or 

intentionally damaged, altered or misused. 

 
b) the equipment is properly installed, adjusted, 

operated and maintained in accordance with 
national and local codes and in accordance with 
the installation instructions provided with this 
product. 

 
c)  the warranty serial number affixed to the appliance 

by us has not been defaced, obliterated or 
removed. 

 
d) an acceptable report for any claim under this 

warranty is supplied to us. 

 

The equipment warranty coverage remains in force for 
one (1) year (parts and labor) from the date the 
equipment is put into operation and two (2) years 
(parts only) for the microprocessor controller, motor 
speed controller and upper platen (aluminum casting 
and shroud). 

 

The Garland Group agrees to repair or replace, at it's 
option, any part that proves to be defective in material 
or workmanship at no charge for the part or normal 
labor. 
 
We assume no responsibility for installation, 
adjustments, diagnosis, or normal maintenance such 
as: lubrication of springs or valves. We exclude 
failures caused by erratic voltage or gas supplies. We 
assume no responsibility for travel costs beyond 100 
miles round trip, travel other than overland, and 
overtime costs of repair. We exclude broken glass, 
paint and porcelain finish, surface rust, gasket 
material, ceramic material, light bulbs and fuses from 
normal coverage. We exclude damage or dysfunction 
caused by fire, flood, and like "Acts of God" that are 
beyond the control of The Garland Group. 
 
The Garland Group’s liability on a claim of warranty 
shall not exceed the price of the material and/or 
service, which caused the claim. This warranty is 
limited and is in lieu of all other warranties, expressed 
or implied. The Garland Group, our employees, or our 
agents shall not be held liable for any claims of 
personal injury or consequential damage or loss. This 
warranty gives you specific legal rights, and you may 
have other rights which vary from state to state. 
 

INTRODUCTION 

 
The Garland clamshell grill, manufactured exclusively 
for McDonald's, provides a method for efficient two-

sided cooking, while accommodating a variety of 
products. The unit will also serve as a flat grill, and 
meets all of McDonald's standards for safety, 
efficiency, and cleanliness. 
 

SHIPPING DAMAGE CLAIM PROCEDURE 

 
Please note that the Garland equipment was  carefully 
inspected and packed by skilled personnel before 
leaving the factory.  The transportation company 
assumes full responsibility for safe delivery upon 
acceptance of the equipment. 
 
What to do if the equipment arrives damaged: 
 
1.  File a claim immediately regardless of the extent 

of damage. 

 
2.  Be sure to note, "visible loss or damage," on the 

freight bill or express receipt and have the person 
making the delivery sign it. 

 
3. Concealed loss or damage:  if damage is 

unnoticed until the equipment is unpacked, notify 
the freight company immediately, (within 15 days), 
and file a concealed damage claim. 

 

SAFETY 

 
Always follow these safety precautions when operating 
the clamshell grill. 
 
This grill must only be operated by persons who have 
been given adequate training. 
 
CAUTION: THIS EQUIPMENT MUST ONLY BE 

OPERATED UNDER AN APPROVED 
HOOD SYSTEM. 

 
DO NOT OPERATE THE GRILL UNLESS IT HAS  

BEEN COMMISSIONED (START-UP) BY 
A FACTORY AUTHORIZED SERVICE 
CENTER. 

 
DO NOT
 operate the grill without reading this 

 

operation manual. 

 
DO NOT operate the clamshell grill unless it has been 

properly installed and grounded. 

 
DO NOT operate the clamshell grill unless all service 

and access panels are in place and fastened 
properly. 

 
The Garland clamshell grill is a semi-automatic 
cooking appliance. The upper platen is lowered 
Automatically, following the manual, two-handed 
initiation of the cooking cycle, and the upper platen is 
raised automatically upon completion of the cooking 
cycle. 
 

Содержание MWGH-9501





































Отзывы: