Gardner Denver GD Connect 12 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 60

background image

1. Foreword

4

1.3 Notes

General

These operating instructions are intended to familiarize
the user with the control and its intended use. The
instructions contain important notes on how to operate
the control safely, properly and cost effectively.
Observing these instructions helps to avoid risks, to
reduce repair costs and downtimes and to increase the
reliability and service life of the control.

The operating instructions apply in addition to
applicable national rules and regulations regarding the
prevention of accidents and environmental protection.
They must be kept available at all times at the place of
use of the control. The operating instructions must be
read and observed by any person carrying out work in
connection with the control, e.g. operation, including
setting up, fault-finding during operating cycles,
disposal of production waste, care, service, and
disposal of waste fuels and consumables, upkeep
(maintenance, inspection, repair), transport.

In addition to the operating instructions and the binding
regulations for the prevention of accidents which apply
in the country and place of operation of the control, the
generally accepted technical rules for safe and proper
working must also be observed.

Guarantee

Operate the control only if you have familiarized
yourself with the control and these operating
instructions.

Gardner Denver cannot be held responsible for the safe
operation of the control if it is used in a manner which
does not correspond to the intended use, or for
applications other than those mentioned in these
instructions.

Warranty claims will not be accepted in the case of:

Operating errors

Use of spare parts other than Gardner Denver
original spare parts
Modifications and changes to the installation.

The above exclusions do not extend the scope of the
warranty and liability conditions of the general terms
and conditions of Gardner Denver.

Any unauthorized changes to the control or the
installation of components not approved by the
manufacturer will result in the withdrawal of the CE
mark. As a consequence, any liability and warranty
claims will not be accepted by the manufacturer.

Safety instructions

Danger

The safety instructions in chapter 3 of the operating
instructions must be strictly observed.

«
...
2
3
4
5
6
...
»

Содержание GD Connect 12





























































Отзывы:

Нет отзывов

Похожие инструкции для GD Connect 12

Бренд: Baby Trend Страницы: 10

Бренд: RAKwireless Страницы: 6

Бренд: Vanderbilt Страницы: 2

Бренд: Water Specialist Страницы: 60

Бренд: Vaillant Страницы: 12

Бренд: NAiS Страницы: 144

Бренд: Parker Страницы: 4

Бренд: cinetto Страницы: 56

Бренд: Riello Страницы: 72

Бренд: C-TEC Страницы: 28

Бренд: Nacon Страницы: 46

Markoprint iJET

Бренд: Weber Страницы: 127

Easyflow J7 DN15

Бренд: Neles Страницы: 12

Бренд: Absima Страницы: 42

Бренд: DIEL Страницы: 30

Бренд: Enttec Страницы: 4

Бренд: Bardiani Страницы: 114

ISaGRAF mPAC Series

Бренд: ICP DAS USA Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды