Gardner Denver GD Connect 12 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 60

background image

9. Webserver module

43

9.4 Connection to the GD Connect 12

The module is connected to the GD Connect 12 via the
built-in RS485 interface.

The Webserver module will be delivered with a 3 wire
connection cable (1m).
This will be connected to the RS485-3 of the GD
Connect 12.

For longer distances, the cable should be removed and
an appropriate cable is to create.

The wiring diagram that shows how to connect the
RS485 interface to the GD Connect 12 can be found in
the annex.

After the connection of the Webserver module, the
RS485-3 interface of the GD Connect 12 has to be
adjusted to enable the communication to the GD
Connect 12.

There, in the menu "Adjustments GD Connect 12" –
"RS485 interface" the menu item "Protocol/module" has
to be adjust to "Webserver module".

9.5 Connection to the net work

The Webserver module will be delivered with an
installed Ethernet connection cable (Cat.5E, Type
100Base-TX, 3m).

When installing this cable, it is necessary to ensure that
it is not bent or stretched and the shield and the locking
lugs of the plug are not damaged.

For longer distances, the cable should be removed and
an appropriate cable is to create.

To ensure the continued water protection, the cable
must be leaded through a suitable M20 gland before the
assembly.

9.6 Access via browser

Within the Webserver module a HTTP-Server is
integrated which can be accessed via web browser.

Suitable are (inter alia) the current versions of

Microsoft Internet Explorer
Mozilla Firefox

Also the Adobe Flash Player has to be installed (version
9.0 or higher). It is to find for the appropriate web
browser and for the appropriate operating system

either onto the CD, which will be delivered with the
GD Connect 12

or in the internet.

9.7 Configuration

For the first configuration of the Webserver module a
fixed IP address can be forced.

Therefore the DIP switches 1 and 2 must be set to „On“
and then the module must be reboot.
After this, the module is accessible at the IP address
„192.168.2.1“ and can be reconfigured.

The following parameters can be adjusted:

Hostname
Switch on and off the usage of DHCP
IP address
Netmask
Gateway
DNS server

After the configuration, the DIP switches can be reset

and the module must be reboot

.

«
...
41
42
43
44
45
...
»

Содержание GD Connect 12





























































Отзывы:

Нет отзывов

Похожие инструкции для GD Connect 12

Бренд: Samson Страницы: 100

Бренд: Danfoss Страницы: 16

Бренд: Radio Shack Страницы: 3

Бренд: XBOX Страницы: 2

Бренд: Access Страницы: 12

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Cypress Страницы: 3

IB-TRON 4000 SOL

Бренд: INSBUD Страницы: 14

Бренд: babyplus Страницы: 28

Turbo-V 250 series

Бренд: Varian Страницы: 79

Бренд: M-system Страницы: 7

Бренд: EBS Страницы: 116

Бренд: Daikin Страницы: 2

GreenMax DRC DRC07-ED0

Бренд: Leviton Страницы: 2

Бренд: Estun Страницы: 41

Elan SRB 201ZH X3

Бренд: schmersal Страницы: 6

Бренд: Phylrich Страницы: 3

Бренд: salmson Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды