Gardner Denver GD Connect 12 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 60

background image

4. Features of the system

17

4.5 Scope of delivery

After receipt, check the scope of delivery:

GD Connect 12 control cabinet
incl. cable glands

2 coded plugs (4-pin)
for the RS485-1 and RS485-3 interfaces

Line pressure sensor

Plug kit to connect the compressor controllers

SD card

Wiring diagram

CD-ROM with manuals

Quick Start Guide incl. drill template for mounting
The drill template can also be found in the annex.

4.6 System components

Analog inputs

There are two analog inputs (4..20mA) on the GD
Connect 12:

Analog input AI-1
This is fixed assigned to the "Line pressure 1" function.
The scaling is adjustable in the menu "Adjustments GD
Connect 12 " menu, "Inputs/Outputs" sub-menu.
Either a passive or active 4..20mA sensor can be used.

Analog input AI-2
This input can be set to different functions and scalings
in the menu "Adjustments GD Connect 12" ,
"Inputs/Outputs" sub-menu.
Either a passive or active 4..20mA sensor can be used.

Information on how to connect the analog inputs can be
found in the annex.

General information on connecting compressors

Compressors are connected to the GD Connect 12 via
the RS485-1 interface only.

The RS485 interfaces of the GD Connect 12 and the
compressor controls should form a bus structure, i.e. all
compressors are connected in series, starting from the
GD Connect 12.

Fig. 3 shows examples of correct and incorrect wiring of
the compressor station.

C1 . .C3

Fig. 3 – Wiring of the compressor station

Connecting Gardner Denver compressors

GD compressors can be connected directly to the GD
Connect 12 via their RS485 interfaces.

Note

In order to operate correctly, the appropriate minimum
software version must be installed on the controllers.
The minimum software versions are listed in the
overview in section 4.2.

Note that the RS485 interfaces of the compressor
controls have been set to the correct values for

Protocol
Baudrate
Address

Further information on the connections (wiring diagrams
and compressor control settings) can be found in the
annex.

C1

C2

C3

Incorrect

GD

Conn.12

GD

Conn.12

C1

C2

C3

Correct

C1

C2

C3

GD

Conn.12

Incorrect

GD

Conn.12

C1

C2

C3

Correct

«
...
15
16
17
18
19
...
»

Содержание GD Connect 12





























































Отзывы:

Нет отзывов

Похожие инструкции для GD Connect 12

Бренд: Valve Concepts Страницы: 15

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

Бренд: BADODOSECURITY Страницы: 8

Бренд: Samson Страницы: 40

Бренд: IBM Страницы: 38

Бренд: Panasonic Страницы: 8

PDS CONTROL Series

Бренд: S&P Страницы: 32

Бренд: asalvo baby Страницы: 84

Бренд: GEM Страницы: 17

Бренд: Simplex Страницы: 40

Бренд: HomeMatic Страницы: 36

Бренд: Kohler Страницы: 48

AUTOPULSE IQ-318

Бренд: Notifier Страницы: 62

Бренд: CALEFFI Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды